Cisco MX Series Скачать руководство пользователя страница 31

Страница: 31 / 33

Cisco VCS provisioning

When using the Cisco VCS (Video Communication Server)

provisioning, a template containing all the settings that can be

provisioned must be uploaded to Cisco TMS (TelePresence

Management System). This is called the

Cisco TMS provision-

ing configuration template

All the advanced settings for your video system are included

in this template. All settings except

SystemUnit Name

and

SIP

Profile [1..1] URI

can be automatically provisioned to the video

system.

The advanced settings are described in the administrator guide

for your video system.

Read the Cisco TMS Provisioning Deployment Guide to find

out how to upload the file to Cisco TMS, and how to set

the desired values for the parameters to be provisioned. If

not set by Cisco TMS, the default values are used. Go to:



http://www.cisco.com/c/en/us/support/conferencing/

telepresence-management-suite-tms/products-installation-

and-configuration-guides-list.html

Download the provisioning configuration

template

You can download the templates here:

MX Series:



MX Series Release Notes

SX Series:



SX Series Release Notes

For each software release there is one provisioning configu-

ration template for every video system model. Make sure to

download the correct file.

Cisco TelePresence Video Systems

D15318.02 Video Systems Getting Started Guide CE8.1, APRIL 2016.

Getting Started Guide

Introduction

User interfaces

Web interface

On-screen setup assistant

Appendices



Touch

Appendices

Содержание MX Series


































Результаты поиска

Содержание MX Series

Отзывы:

Бренды по названию

Популярные бренды

Cisco MX Series, Руководство по началу работы

Результаты поиска

Содержание MX Series

Отзывы:

Бренды по названию

Популярные бренды