Cisco FM1200 Volo Скачать руководство пользователя страница 64

Страница: 64 / 175

Figure 26. Configurator GUI (Wireless Radio dialog)

Enter a defined network passphrase in the Shared Passphrase
field.

IMPORTANT

If a shared pass phrase is defined, the
samepass phrase must be used for all Cisco units
inthe same network.

The shared pass phrase can be composed of
anyASCII characters except the following:

'`"\$=

Specify the country in which the unit is installed by selecting the
correct option from the

Country

drop-down menu.

CAUTION

Different

countries

frequently

have

differing

telecommunications regulations. If the Country listing
is not set correctly, the unit may violate national
telecommunications legislation.

Specify the unit's operating frequency by clicking the correct
option in the

Frequency (MHz)

drop-down.

CAUTION

Make sure that the chosen country listing matches
the country in which the unit is installed before
changing the

Frequency (MHz)

value.

• You can change the frequency of each radio link in order to

minimize interference with other wireless networks

Device configuration using the configurator interface

Page 64 of 175

Содержание FM1200 Volo
















































































































































































Результаты поиска

Содержание FM1200 Volo

Отзывы:

Похожие инструкции для FM1200 Volo

Бренды по названию

Популярные бренды

Cisco FM1200 Volo, Руководство по установке и настройке

Результаты поиска

Содержание FM1200 Volo

Отзывы:

Похожие инструкции для FM1200 Volo

Бренды по названию

Популярные бренды