Cisco FM1200 Volo Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 175

background image

CAUTION

Make sure that you download the specific *.BIN file
for your device type. Uploading incorrect firmware for
the device type will cause the firmware overwrite to
fail, and may damage the unit.

The following procedure describes how to overwrite the existing firmware
on a Cisco device. This procedure assumes that the wireless networkis
currently active.

To overwrite the existing firmware on the Cisco device, do the
following steps:

1.

Power OFF all Cisco devices connected to the wireless
network.
Disconnect all Ethernet cables from the Cisco device.

2.
3.

With the Cisco device disconnected from the wireless
network, power ON the device.

CAUTION

Do not restart or power OFF the device while
firmware overwriting is in progress.

Restarting or powering OFF the unit before
overwriting is complete will permanently damage the
unit.

4.

Connect the computer containing the firmware image file directly
to the Cisco unit, using an Ethernet cable. For detailed
information on direct connection, refer to

“Accessing the Cisco

FM1200 Volo for device configuration” (page 47)

.

5.

As a precaution, save the unit's existing device configuration file
to the computer. For detailed information on how to save the
existing configuration file, refer to

“Saving and restoring the unit

settings” (page 136)

.

6.

Click the

-firmware upgrade

link under

MANAGEMENT

SETTINGS

in the left-hand settings menu.

• The

UPGRADE

FIRMWARE

shown

be

will

dialog

Figure 56 (page 130)

).

Device configuration using the configurator interface

© 2021 Cisco and/or its affiliates. All rights reserved.

Page 129 of 175

«
...
127
128
129
130
131
...
»

Содержание FM1200 Volo
















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FM1200 Volo

Бренд: Icom Страницы: 5

Бренд: Parkside Страницы: 65

Бренд: Sandstrom Страницы: 36

C-Tech HD 6600 SST

Бренд: Clarke-tech Страницы: 32

Бренд: Retekess Страницы: 2

Бренд: IDT Страницы: 25

Бренд: HobbyKing Страницы: 2

Long Range Transmitter 2

Бренд: Gatekeeper Systems Страницы: 5

Бренд: Ashcroft Страницы: 2

Бренд: Marantz Страницы: 101

Бренд: Yaesu Страницы: 32

Бренд: Seli Страницы: 69

Бренд: Videotec Страницы: 37

IN-Command AVR-X4000

Бренд: Denon Страницы: 224

Бренд: MobileBlackBox Страницы: 9

Бренд: Darwin Страницы: 6

Бренд: Cobra Страницы: 8

Бренд: Cobra Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды