Cisco FM1200 Volo Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 175

background image

IMPORTANT

If  TITAN  is  enabled  at  core  network  level  and  dual-
redundant  global  gateway  units  are  installed,  do  not
enter the global gateway's actual Mesh ID number as
the  Destination  Address.  Instead,  use  Destination
Address

5.0.0.0

3.

Enable downstream (infrastructure to vehicle) Multicast traffic by
adding multicast route

224.5.5.6 / 5.255.255.255

to the global

gateway unit,

and

to the Mesh End unit in each subnet cluster.

NOTE

5.255.255.255

is the wildcard address for all Mesh ID

destinations within the network.

7.6.5. SNMP configuration

The SNMP window can be used to configure an SNMP v2c or SNMP v3
service to run on the Cisco FM1200 Volo.

Walk-throughs  (no  agent-to-manager  notifications)  and  traps  (agent-to-
manager  notifications  enabled)  are  both  supported.  If  SNMP  traps  are
enabled,  you  can  specify  the  server  address  to  which  monitoring
information must be sent.

IMPORTANT

The same SNMP configuration must be set for all Cisco
units in the wireless network.

For detailed information on Cisco unit SNMP
configuration, refer to the

Cisco SNMP FM-MIB OID Table

and MIB configuration files. These can be downloaded from
the Cisco Partner Portal (

Documentation

section >

User

Manuals

>

Advanced Manuals

.)

To change the SNMP settings, do the following steps:

•

Click the

-snmp

mode link under

ADVANCED SETTINGS

in the

left-hand settings menu.

• The default

SNMP

dialog will be shown (

Figure 43 (page

Device configuration using the configurator interface

© 2021 Cisco and/or its affiliates. All rights reserved.

Page 104 of 175

«
...
102
103
104
105
106
...
»

Содержание FM1200 Volo
















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FM1200 Volo

Бренд: Datawell Страницы: 37

Бренд: MadgeTech Страницы: 4

wM-Bus 868 USB Key

Бренд: MADD Страницы: 4

Бренд: M-system Страницы: 18

Бренд: RF Limited Страницы: 4

Бренд: JETI model Страницы: 33

Бренд: Tivoli Audio Страницы: 16

Бренд: KBSOUND Страницы: 16

Бренд: Artistic Licence Страницы: 43

FatMax FMHT1-77360

Бренд: Stanley Страницы: 154

Бренд: Sencore Страницы: 3

IN-Command AVR-X4000

Бренд: Denon Страницы: 224

Бренд: Strong Страницы: 29

Бренд: AOR Страницы: 45

Бренд: rtd Страницы: 2

Бренд: BriarTek Страницы: 10

Бренд: GAMA Electronics Страницы: 4

Бренд: Safeguard Supply Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды