manualshive.com logo in svg

Cisco Cisco ONS 15600 SDH, Руководство по устранению неисправностей

Продукт Cisco ONS 15600 SDH - это мощное устройство для оптоволоконной связи. У вас возникли проблемы с оборудованием? Скачайте бесплатно Руководство по устранению неисправностей на manualshive.com. Наша подробная инструкция поможет вам быстро и эффективно решить любую проблему.

Поделиться
Скачать
background image

2-97

Cisco ONS 15600 SDH Troubleshooting Guide, R8.0

July 2010

Chapter 2 Alarm Troubleshooting

2.6.148   MS-AIS

  •

A 1+1 APS is identified on the node view Maintenance > Protection tab. If you click the protection 
group, under the Selected Group list, the ports are designated as Working/Standby and 
Protect/Active.

Step 3

If the reporting port is part of an SNCP, complete the 

“Initiate a Force Switch for All Circuits on a SNCP 

Span” procedure on page 2-126

. If the port is part of a 1+1 protection group, complete the 

“Initiate a 1+1 

Protection Port Force Switch Command” procedure on page 2-123

.

Step 4

If the reporting card is a SSXC card and an automatic switch to the preferred copy SSXC card occurred, 
traffic automatically switches to the alternate copy. 

Complete a 

“Hard-Reset a Card Using CTC” procedure on page 2-131

 for the reporting card (or 

“Soft-Reset a Card Using CTC” procedure on page 2-130

 for the SSXC.

Step 5

If the reset does not clear the alarm, complete the 

“Reset a Card with a Card Pull (Reseat)” section on 

page 2-133

 for the TSC card, or complete the 

“Request a Cross-Connect Card Preferred Copy Switch” 

section on page 2-132

 for the SSXC.

Step 6

If the physical reseat of the card or switch does not clear the alarm, complete the appropriate procedure 
in the 

“Replace a TSC Card” section on page 2-136

 or 

“Replace an SSXC Card” section on page 2-133

 

as needed.

Note

If the traffic (STM-N) card is implicated and you are able to continue using the traffic card with 
one port out of service, perform a bridge and roll to move the port traffic to a free port using the 
“Bridge and Roll Traffic” procedure in the “Manage Circuits” chapter in the 

Cisco ONS 15600 SDH Procedure Guide

. Label the bad port, and place it out of service until 

such time as the card can be replaced.

Step 7

If the MFGMEM alarm continues to report after you replaced the card, the problem lies in the EEPROM. 
Log into the Technical Support Website at http://www.cisco.com/techsupport for more information or 
call Cisco TAC (1 800 553-2447).

Step 8

If the alarm clears and it was reported by a traffic card, traffic reverts to the working port if an automatic 
switch occurred. If traffic was manually switched in a 1+1 protection group, revert traffic to the original 
port by completing the 

“Clear a 1+1 Protection Port Force or Manual Switch Command” procedure on 

page 2-124

. If traffic was manually switched in an SNCP, revert traffic to the original path by completing 

the 

“Clear a SNCP Span External Switching Command” procedure on page 2-127

.

If an automatic switch to the alternate copy SSXC card occurred, traffic is automatically restored to the 
preferred copy. 

Step 9

If the reporting card is a TSC card and you want to make the standby TSC card active again, complete 
the 

“Soft-Reset a Card Using CTC” procedure on page 2-130

.

2.6.148  MS-AIS 

Default Severity: Not Reported (NR), Non-Service-Affecting (NSA)

Logical Object: STMN

The Multiplex Section (MS) AIS condition indicates that there is a defect in the multiplexing section 
layer of the SDH overhead. The multiplex section refers to the segment between two SDH devices in the 
circuit and is also known as a maintenance span. The multiplex section layer of the SDH overhead deals 
with payload transport, and its functions include multiplexing and synchronization.

Содержание Cisco ONS 15600 SDH































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cisco ONS 15600 SDH

Jetter JXM-IO-E30 Installation Manual preview
JXM-IO-E30
Бренд: Jetter Страницы: 35
Lantronix Device Server UDS 10 Hardware Manual preview
Device Server UDS 10
Бренд: Lantronix Страницы: 8
X-Micro WLAN 11g User Manual preview
WLAN 11g
Бренд: X-Micro Страницы: 74
XIA Pixie-4 Express Software Manual preview
Pixie-4 Express
Бренд: XIA Страницы: 17
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Бренд: Ruckus Wireless Страницы: 56
Renesas RSKH836079 Quick Start Manual preview
RSKH836079
Бренд: Renesas Страницы: 6
Dazzle Hollywood DV-Bridge User Manual preview
Hollywood DV-Bridge
Бренд: Dazzle Страницы: 63
IntesisBox IBOX-BAC Series Installation Sheet preview
IBOX-BAC Series
Бренд: IntesisBox Страницы: 2
Linksys WRT54GR - Wireless-G Broadband Router Quick Installation Manual preview
WRT54GR - Wireless-G Broadband Router
Бренд: Linksys Страницы: 81
Avaya XM24 Expansion Module Installation Instructions preview
XM24 Expansion Module
Бренд: Avaya Страницы: 5
ICP DAS USA I-87K Series User Manual preview
I-87K Series
Бренд: ICP DAS USA Страницы: 31
ExtraHop EDA 4200 Install preview
EDA 4200
Бренд: ExtraHop Страницы: 2
BinTec BinGO! DSL II Quick Install Manual preview
BinGO! DSL II
Бренд: BinTec Страницы: 2
Grizzly PSJ-VZ58 gen3 OEM User Manual preview
PSJ-VZ58 gen3 OEM
Бренд: Grizzly Страницы: 12
MEN ME4 User Manual preview
ME4
Бренд: MEN Страницы: 48
Belkin F9K1002V1 User Manual preview
F9K1002V1
Бренд: Belkin Страницы: 42
Delta Electronics DVP Series PLC DVP04TC-H2 Instruction Manual preview
DVP Series PLC DVP04TC-H2
Бренд: Delta Electronics Страницы: 2
Billion BiPAC 645 Quick Start Manual preview
BiPAC 645
Бренд: Billion Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды