Cisco Catalyst 6816-X-LE Скачать руководство пользователя страница 29

Страница: 29 / 100

Status LED

The status LED indicates the status of the system.

Table 7: Status LED Indicator

Description

Color/State

System is not operational.

Off

System is operating normally without alarms.

Green

System has triggered a minor environmental alarm.

Amber

System has triggered a major environmental alarm.

Red

System ID LED

The System ID (blue beacon) LED can be provisioned by the operator to indicate that the switch needs
attention.

Table 8: System ID LED Indicator

Description

Color/State

The system needs attention.

Blinking blue

Management Port LED

This table describes the management port LEDs.

Table 9: Management Port LED Indicator

Description

Color/State

Port is not provisioned.

Off

Port is provisioned, but administratively not operational.

Amber

Port is linked up.

Green

A port fault is detected, or the port beacon has been provisioned by
the operator.

Alternating green and amber

Fan Tray LED

The Fan LED is located on the front panel of the switch. The following image depicts the Fan LED, the system
status LED, and the blue beacon LED on the front panel of the switch.

Catalyst 6840-X Switch Series Hardware Installation Guide

Product Overview

Status LED

Содержание Catalyst 6816-X-LE





































































































Результаты поиска

Содержание Catalyst 6816-X-LE

Отзывы:

Похожие инструкции для Catalyst 6816-X-LE

Бренды по названию

Популярные бренды

Cisco Catalyst 6816-X-LE, Руководство по установке оборудования

Результаты поиска

Содержание Catalyst 6816-X-LE

Отзывы:

Похожие инструкции для Catalyst 6816-X-LE

Бренды по названию

Популярные бренды