Cisco Catalyst 3550 страница 58 Скачать руководство пользователя

Страница: 58 / 154

Chapter 2 Installing and Starting the Switch

Installing the Switch

2-8

Catalyst 3550 Multilayer Switch Hardware Installation Guide

78-11358-03

–

Two 23-inch rack-mounting brackets (with 1-inch spacing for telco
racks)

–

Four number-8 Phillips truss-head screws for attaching the brackets to
the switch

–

Two number-12 Phillips machine screws for attaching the brackets to a
rack

Note

The DC-switch kit ships only with the Catalyst 3550-24-DC switch.

•

One RJ-45-to-DB-9 adapter cable

•

Cisco Information Packet, containing warranty, safety, and support
information

Installing the Switch

These sections describe the steps required to install the switch in a rack, on a wall
or on a table or shelf.

Rack Mounting

Warning

To prevent bodily injury when mounting or servicing this unit in a rack, you must
take special precautions to ensure that the system remains stable. The
following guidelines are provided to ensure your safety:

•

This unit should be mounted at the bottom of the rack if it is the
only unit in the rack.

•

When mounting this unit in a partially filled rack, load the rack
from the bottom to the top with the heaviest component at the
bottom of the rack.

•

If the rack is provided with stabilizing devices, install the
stabilizers before mounting or servicing the unit in the rack.

Содержание Catalyst 3550



























































































































































Результаты поиска

Содержание Catalyst 3550

Отзывы:

Похожие инструкции для Catalyst 3550

Бренды по названию

Популярные бренды

Cisco Catalyst 3550, Руководство по установке

Результаты поиска

Содержание Catalyst 3550

Отзывы:

Похожие инструкции для Catalyst 3550

Бренды по названию

Популярные бренды