manualshive.com logo in svg

Cisco Catalyst 3550, Руководство по установке

Поделиться
Скачать
Cisco Catalyst 3550 Скачать руководство пользователя страница 57

 

2-7

Catalyst 3550 Multilayer Switch Hardware Installation Guide

78-11358-03

Chapter 2      Installing and Starting the Switch

Preparing for Installation

Verifying Package Contents

Note

Carefully remove the contents from the shipping container, and check each item 
for damage. If any item is missing or damaged, contact your Cisco representative 
or reseller for support. Return all packing material to the shipping container, and 
save it.

The switch is shipped with these items:

•

This Catalyst 3550 Multilayer Switch Hardware Installation Guide

•

Where to Find the Catalyst 3550 Documentation flyer

•

Cisco Documentation CD-ROM

•

AC power cord

•

Mounting kit containing:

–

Four rubber feet for mounting the switch on a table

–

Two 19-inch rack-mounting brackets

–

Four Phillips flat-head screws for attaching the brackets to the switch 
(Catalyst 3550-12T and 3550-12G)

–

Six Phillips flat-head screws for attaching the brackets to the switch 
(Catalyst 3550-24,  3550-48, 3550-24-FX, and 3550-24-DC)

–

Four Phillips machine screws for attaching the brackets to a rack

–

One cable guide and one black Phillips machine screw for attaching the 
cable guide to one of the mounting brackets

–

One RPS connector cover (for wall mounting)

–

Two Phillips pan-head screws (for attaching the RPS cover)

–

Four Phillips truss-head screws (for wall-mounting brackets)

•

DC-switch kit containing these items:

–

One DC terminal block plug (also called a terminal block header)

–

One ground lug

–

Two number-10-32 screws for attaching the ground lug to the switch

Содержание Catalyst 3550



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды