manualshive.com logo in svg

Cisco Catalyst 3130, Руководство по настройке программного обеспечения

Cisco Catalyst 3130 - сетевой коммутатор с широкими возможностями управления и конфигурации. Пользователи могут загрузить бесплатное руководство по настройке программного обеспечения с официального сайта. Настройте свою сеть с легкостью, следуя инструкциям в Software Configuration Manual для Catalyst 3130. Более подробную информацию можно найти на manualshive.com.

Поделиться
Скачать
background image

 

16-7

Cisco Catalyst Blade Switch 3130 and 3032 for Dell Software Configuration Guide

OL-12247-04

Chapter 16      Configuring Private VLANs

Configuring Private VLANs

Private-VLAN Configuration Guidelines

Guidelines for configuring private VLANs fall into these categories:

•

Secondary and Primary VLAN Configuration, page 16-7

•

Private-VLAN Port Configuration, page 16-8

•

Limitations with Other Features, page 16-9

Secondary and Primary VLAN Configuration

Follow these guidelines when configuring private VLANs:

•

If the switch is running VTP version 1 or 2, you must set VTP to transparent mode. After you 
configure a private VLAN, you should not change the VTP mode to client or server. For information 
about VTP, see see 

Chapter 14, “Configuring VTP.”

 VTP version 3 supports private VLANs in all 

modes.

•

With VTP version 1 or 2, after you have configured private VLANs, use the 

copy running-config 

startup config 

privileged EXEC command to save the VTP transparent mode configuration and 

private-VLAN configuration in the switch startup configuration file. Otherwise, if the switch resets, 
it defaults to VTP server mode, which does not support private VLANs. VTP version 3 does support 
private VLANs.

•

VTP version 1 and 2 do not propagate private-VLAN configuration. You must configure private 
VLANs on each device where you want private-VLAN ports unless the devices are running VTP 
version 3. 

•

You cannot configure VLAN 1 or VLANs 1002 to 1005 as primary or secondary VLANs. Extended 
VLANs (VLAN IDs 1006 to 4094) can belong to private VLANs

•

A primary VLAN can have one isolated VLAN and multiple community VLANs associated with it. 
An isolated or community VLAN can have only one primary VLAN associated with it. 

•

Although a private VLAN contains more than one VLAN, only one Spanning Tree Protocol (STP) 
instance runs for the entire private VLAN. When a secondary VLAN is associated with the primary 
VLAN, the STP parameters of the primary VLAN are propagated to the secondary VLAN. 

•

You can enable DHCP snooping on private VLANs. When you enable DHCP snooping on the 
primary VLAN, it is propagated to the secondary VLANs. If you configure DHCP on a secondary 
VLAN, the configuration does not take effect if the primary VLAN is already configured.

•

When you enable IP source guard on private-VLAN ports, you must enable DHCP snooping on the 
primary VLAN. 

•

We recommend that you prune the private VLANs from the trunks on devices that carry no traffic 
in the private VLANs.

•

You can apply different quality of service (QoS) configurations to primary, isolated, and community 
VLANs.

•

Sticky ARP

–

Sticky ARP entries are those learned on SVIs and Layer 3 interfaces. They entries do not age 
out.

–

The 

ip sticky-arp

 global configuration command is supported only on SVIs belonging to 

private VLANs.

Содержание Catalyst 3130











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3130

Genetec SV-32 Quick Start Manual preview
SV-32
Бренд: Genetec Страницы: 16
Symantec 10521148 - Network Security 7161 Implementation Manual preview
10521148 - Network Security 7161
Бренд: Symantec Страницы: 214
SMC Networks 2504W - FICHE TECHNIQUE Overview preview
2504W - FICHE TECHNIQUE
Бренд: SMC Networks Страницы: 2
Barracuda QSG 4.X Quick Start Manual preview
QSG 4.X
Бренд: Barracuda Страницы: 2
Advantech FWA-3140 User Manual preview
FWA-3140
Бренд: Advantech Страницы: 23
SonicWALL Internet Security Quick Start Manual preview
Internet Security
Бренд: SonicWALL Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды