Cisco CableCARD Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 184

background image

Appendix C

Setting Up Multiple Bootloader Carousels

138

734375 Rev H

Determining Available Bandwidth for BFS BIG Systems

This section provides procedures for operators with a BFS BIG to use in determining
how much bandwidth is available for inband sources. To determine the amount of
bandwidth available for additional bootloader carousels, perform the following
calculation:

Total Available Bandwidth - Bandwidth in Use = Available Bandwidth

Notes:



The inband data rate for a 64-QAM is 25 Mbps.



The inband data rate for a 256-QAM is 36 Mbps.

1

Open an xterm window on the DNCS.

2

Type one of the following, based on the system release you have installed:



For SR 4.2.1 and earlier, type

cd /export/home/dncs/doctor

and press

Enter

.



For SR 4.3 and later, type

cd /dvs/dncs/Utilities/doctor

and press

Enter

.

Note:

Be sure to type a space between

cd

and

/

.

Result:

The current directory is now the doctor directory.

3

Type

doctor -bv

and press

Enter

. A table appears and lists the inband and out-of-

band data rates on the BFS carousel. The total inband carousel bandwidth in use
is displayed in the

Aggregate IB Carousel Datarate

field.

4

Add

1 Mbps

to the data rate in the

Aggregate IB Carousel Datarate

field to

account for any overhead.

Example:

If you have a total inband data rate of 14 Mbps, add 1 Mbps for a total

of 15 Mbps in use.

14 + 1 = 15

5

Subtract the total inband carousel bandwidth in use from the total available
bandwidth to determine the unused inband bandwidth on the BFS.

Examples:



64-QAM:

From the examples above, the available bandwidth is 10 Mbps.

25 - 15 = 10 Mbps



256-QAM:

From the examples above, the available bandwidth is 21 Mbps.

36 - 15 = 21 Mbps

6

Compare the amount of unused bandwidth to the amount of bandwidth
required for the additional bootloader carousels.

«
...
146
147
148
149
150
...
»

Содержание CableCARD

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CableCARD

Бренд: B&B Electronics Страницы: 2

Бренд: µ-Dimension Страницы: 6

Бренд: µ-Dimension Страницы: 17

Бренд: µ-Dimension Страницы: 16

Бренд: µ-Dimension Страницы: 6

Бренд: µ-Dimension Страницы: 8

Бренд: Hagerman Technology Страницы: 9

Бренд: VMIC Страницы: 48

Бренд: QUAD Страницы: 2

SUNNY TRIPOWER STP 20000TL-30

Бренд: SMA Solar Technology Страницы: 50

Бренд: Fenner Страницы: 12

Бренд: Clever Little Box Страницы: 56

Бренд: Alca Power Страницы: 8

AS-07UR4SYDDB15

Бренд: Hisense Страницы: 59

Бренд: Samlexpower Страницы: 56

Бренд: DieHard Страницы: 24

Бренд: Vacon Страницы: 12

Бренд: Vectra Fitness Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды