Cisco BTS 10200 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 62

background image

4-8

Cisco BTS 10200 Softswitch ISDN Provisioning and Troubleshooting

OL-12436-02

Chapter 4 Maintaining and Troubleshooting the ISDN System

Checking the Status of a Trunk Termination

Trunk Static State Is Set to Locally Blocked

Perform the following steps to check the

TRUNK REASON

field if the

TRUNK STATIC STATE

is set to

locally blocked (LBLK) state.

Step 1

If the TRUNK REASON is set to MAINT-OOS, then a user has manually taken the trunks out of service.
The user must manually put the trunks into the in-service mode.

Use the

control

command on the specified trunk to put the trunk back into the in-service mode.

Clear the MAINT-OOS. Trunks should be in active or idle mode and ready for use.

Step 2

If the TRUNK REASON is set to SIGNALLING-FAULT, then the D channels are not in-service. Check
the D-channels ADMIN and OPER states.

•

If the D-channel ADMIN state is ADMIN_OOS, use the

control

command to put the D-channel into

in-service mode.

•

If the D-channel ADMIN state is ADMIN _INS, verify that the D-channel OPER-STATE is
IN-SERVICE (see the

How to Troubleshoot When the ISDN D-Channel Fails to Restore

case of any issues).

•

Clear any SIGNALLING-FAULT states. Trunks must be in active or idle mode and ready for use.

Step 3

If TRUNK REASON is set to TERM_FAULT, then the terminations are in FAULTY states. Verify the IP
connectivity from the CA to the gateway.

a.

Clear any termination faults at the gateway by turning off, then turning on, MGCP (use the mgcp,
no mgcp procedure on the media gateway).

b.

Clear any TERM_FAULT on the Cisco BTS 10200 Softswitch. Trunks must be in active or idle mode
and ready for use.

Trunk Static State Is Set to TRNS

Perform the following steps when trunk static state is set to TRNS.

Note

If trunk static state is set to TRNS, then the PBX has not responded with a SERVICE_ACK or
RESTART_ACK for the service or restart message set by the Call Agent.

Step 1

Verify that the initialization procedure, as depicted by the associated isdn-dchan-profile, and as used by
PBX, is synchronized.

Step 2

Verify that the isdn-service-supp token is set to N if PBX does not support service messages.

«
...
48
49
50
51
52
...
»

Содержание BTS 10200































































Отзывы:

Нет отзывов

Похожие инструкции для BTS 10200

Бренд: N-Tron Страницы: 20

Edge RTM-ATCA-F140

Бренд: Penguin Страницы: 2

LMP-1204G-SFP Series

Бренд: ANTAIRA Страницы: 20

Бренд: QSFPTEK Страницы: 12

Бренд: hager Страницы: 2

Бренд: HIKVISION Страницы: 25

Бренд: Jerguson Страницы: 16

SmartStack STS16-20R

Бренд: Cabletron Systems Страницы: 258

Бренд: Pathway connectivity solutions Страницы: 34

Бренд: M-system Страницы: 4

Бренд: Voith Страницы: 98

Бренд: H3C Страницы: 39

SecureStack B2 B2G124-48P

Бренд: Enterasys Страницы: 91

Бренд: SEH Страницы: 40

Бренд: Qvis Страницы: 7

EX78900X Series

Бренд: EtherWAN Страницы: 2

Бренд: LogiLink Страницы: 3

Бренд: H3C Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды