manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 748

 

15-122

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

PSTN Trunk Testing

107 Test Line–Data Transmission

The data transmission test line supports 1-way testing of certain voice band data parameters. This 
includes peak to average ratio signal (PAR), slope, quiet termination, and intermodulation distortion test 
signals. 

It should be noted that newer test equipment, like the SAGE 930/935, provides these and other voice 
band data tests for 

both

 directions makes it possible to use one test line to evaluate voice and voice band 

data performance.

108 Test–Digital Loopback

The 108 test line supports testing by means of a digital loopback. The T108 test line feature determines 
the performance of trunks connecting digital exchange switches, including voice over packet (VoP) 
softswitches. BTS 10200 incoming trunks requesting other 1xx-type test lines are routed to shared test 
lines for the requested tests, regardless of which gateway terminates the trunk or which gateway/IAD 
terminates the test line. The T108 test line feature requests a test to be performed within the same 
gateway where the trunk under test (TUT) is terminated, and provides a digital loopback within the 
gateway. The T108 test line feature supports manual and automated testing.

The T108 test line sequence is as follows:

1.

The near-end switch originates the test sequence by placing a test call, identifying the trunk to be 
selected, and the test line number. A digital test pattern generator is used in the test setup shown in 

Figure 15-3

.

2.

The near-end switch uses the trunk identifier to override normal call processing and select only the 
requested trunk. 

3.

The far-end switch responds to the destination number and connects to the T108 test line. The T108 
test line enables a digital loopback. 

4.

When the near-end switch receives answer supervision, it conducts digital test sequences to 
ascertain trunk performance. 

5.

Once the test sequences are completed, the near-end switch releases the test call and both switches 
release the trunk connection. 

6.

The far-end switch can detect if the test connection exceeds a preset time and releases the test 
connection if the preset time is exceeded.

The T108 test line is also used for trunk redirection (wholesale dial) for Internet services where the 
carrier modem termination is integrated into the trunk gateway. In this case, the integral digital stored 
program (DSP) normally supports modem-only transmissions.

109 Test–Echo

The 109 test line supports in-service testing of echo cancellers or echo suppressors.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды