manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 693

 

15-67

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

Enhanced Traffic Measurement

Enhanced Traffic Measurement

The Cisco BTS 10200 supports both traditional PSTN measurements as well as additional requirements 
required by the IP and ATM backbones that the services are offered over. Many of the informational 
elements within the measurement data find their basis in the traditional PSTN TDM network 
implementations with modifications and additions caused by the expanded needs and capabilities of the 
converged network environment. The Cisco BTS 10200 measurement information includes both 
statistical and performance details. The mechanism used to manage the data generated and transported 
from the Cisco BTS 10200 system follows legacy type procedures and are documented in the following 
sections.

Measurement Data Transport and Access

The measurement data collected on the Cisco BTS 10200 can be accessed through several different 
mechanisms. The Command Line Interface, which runs over a telnet or SSH session, is used in the 
examples within this document. Measurement data is also available in CSV or XML format through the 
FTP or SFTP interface. The measurement data can be provisioned and is accessible through the SNMP 
MIB. The supported version of SNMP on the Cisco BTS 10200 is v2c. There is detailed information on 
both of these access mechanisms available in separate operations manuals.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды