manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 624

 

14-50

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 14      General Troubleshooting

Viewing Trace Logs for Throttled Flood of MGCP Messages from Specific Endpoint

Turn on trace in the BTS Call Agent (CA) for MLS, set MGCP on the CA to info5 level and examine 
the BAU code from the MS: 

TC_11.3.1_CA.log:.  .           MGA    00-00 .           |<<<< RECV FROM: 10.1.31.2 

FROM-PORT=2427 TO-PORT=2727 <<<<|

TC_11.3.1_CA.log-.  .           MGA    00-00 .           |ntfy 717 

annc/[email protected] MGCP 1.0 NCS 1.0^M|

TC_11.3.1_CA.log-.  .           MGA    00-00 .           |X: 2B00000007^M|

TC_11.3.1_CA.log-.  .           MGA    00-00 .           |O: A/of(rc=601)^M|  

TC_11.3.1_CA.log-.  .           MGA    00-00 .           ||snd_rcv.c:260 

Error: NEED 

Explanation: The mls-annc-mult-factor token value is lower than the number of announcements existing 
on the MS.

Recommended Action: Provision the mls-annc-mult-factor token value greater than the number of 
announcements on the MS. 

Error: Return Code 601: File not found 

Explanation: MSs are limited to 40 character filenames. These 40 characters include the extension 
(typically a .wav) and the announcement-file-prefix: for example fra_, eng_ and spa_. 

Recommended Action: Change the filename length to less than 40 characters.

Viewing Trace Logs for Throttled Flood of MGCP Messages from 
Specific Endpoint

The BTS 10200 can detect an incoming flood of messages from an individual MGCP-based MGW or 
termination. When such a flood occurs, the BTS 10200 automatically throttles messages coming from 
that specific resource. If the flood condition stops, the system releases the throttle. The system also 
deletes wild-carded messages (for example, RSIP <tid> *@mgw.net) received from any MGW. This 
detection and throttling mechanism is not customer configurable.

The system displays one of the following traces in logs at the INFO3 level:

  •

Message dumped for termIdx=<term id> due to high incoming message rate 

  •

Message dumped for mgIdx=<mg id> due to high incoming message rate

Note

Log info levels are listed in the 

“Logs” section on page C-13

 in 

Appendix C, “Overload Control”

.

Platform Core File Alarm

The Cisco BTS 10200 Softswitch Core File Monitor feature provides Cisco BTS 10200 Softswitch 
customers with an alarm notification whenever a core file is generated on a Cisco BTS 10200 Softswitch 
platform system. The Cisco BTS 10200 Softswitch Core File Monitor feature also removes core files 
automatically when disk space is critically low or when the core file has aged beyond a maximum 
allowable time.

Core files are generated and stored in the bin directory for the binary executable which generated the 
core. The normal procedure to be followed by the operator is to move the core files as they are generated 
to another storage area. The monitoring of core files with alarm notification will remind the system 
operator to perform this process.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды