manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 567

 

13-3

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 13      Network Troubleshooting

Troubleshooting a Network Failure

Verify the Configuration

Step 1

Determine if the problem is an Internet Protocol (IP) address or port configuration mismatch between 
the ITP and the BTS 10200. Enter 

show sctp-assoc id-<sctp-assoc-name>

 on the BTS 10200 EMS.

Step 2

Enter 

show cs7 sua

 on the ITP. 

Step 3

Verify that the remote transport service access point (TSAP) address and the remote port of the SCTP 
association on the BTS 10200 is the same as the local IP address and the local port used by the ITP SCCP 
user adapter (SUA). If the SCTP association is multi-homed, all of the IP addresses should be verified. 
The following example displays properly matched configurations:

CLI>show sctp-assoc id=sctp_assoc3

ID=sctp_assoc3

SGP_ID=itp_2651_1

SCTP_ASSOC_PROFILE_ID=sctp_prof

REMOTE_PORT=14001

REMOTE_TSAP_ADDR1=10.89.232.48

PLATFORM_ID=FSAIN520

DSCP=NONE

IP_TOS_PRECEDENCE=FLASH

LOCAL_RCVWIN=64000

MAX_INIT_RETRANS=5

MAX_INIT_RTO=1000

STATUS=INS

ULP=XUA

Reply: Success: Entry 1 of 1 returned.

c2651-48#show cs7 sua

Sigtran SUA draft version: 14

SUA  Local port: 14001        State: active      SCTP instance handle: 2

Local IP address:                                10.89.232.48

Number of active SUA  peers:                     8

Max number of inbound streams allowed:           17

Local receive window:                            64000

Max init retransmissions:                        8

Max init timeout:                                1000 ms

Unordered priority:                              equal

SCTP defaults for new associations

 Transmit queue depth:   1000           Cumulative sack timeout:   200 ms

 Assoc retransmissions:  10             Path retransmissions:      4     

 Minimum RTO:            1000  ms       Maximum RTO:               1000  ms

 Bundle status:          on             Bundle timeout:            400 ms

 Keep alive status:      true           Keep alive timeout:        10000 ms

Step 4

If there is no mismatch, proceed to Step 5. Otherwise, perform the following procedure:

a.

Correct the mismatch.

b.

Bounce the SCTP association on the BTS 10200. 

c.

Repeat the 

“Verify the Stream Control Transmission Protocol Association Status” section on 

page 13-2

. 

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды