manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 490

 

10-122

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Monitoring Signaling Events

Emergency Trunks Become Locally Blocked—Signaling (153)

The Emergency Trunks Become Locally Blocked alarm (critical) indicates that an emergency trunk 
(CAS, SS7, or ISDN) is locally blocked. To troubleshoot and correct the cause of the Emergency Trunks 
Become Locally Blocked alarm, refer to 

“Emergency Trunks Become Locally Blocked—Signaling 

(153)” section on page 10-157

.

Emergency Trunks Become Remotely Blocked—Signaling (154)

The Emergency Trunks Become Remotely Blocked alarm (critical) indicates that an emergency trunk 
(CAS, SS7, or ISDN) is remotely blocked. To troubleshoot and correct the cause of the Emergency 
Trunks Become Remotely Blocked alarm, refer to 

“Emergency Trunks Become Remotely 

Blocked—Signaling (154)” section on page 10-157

.

Packet Cable Multi-Media Unsolicited Gate Delete—Signaling (155)

The Packet Cable Multi-Media Unsolicited Gate Delete event serves as an informational alert that an 
error condition was encountered by the CMTS. To correct the cause of the event, check the alarms and 
warnings from the CMTS.

Integrated Services Digital Network Signaling Gateway Down—Signaling 
(156)

The Integrated Services Digital Network Signaling Gateway Down alarm (major) indicates that the BTS 
10200 system cannot communicate with the ISDN gateway. To troubleshoot and correct the cause of the 
Integrated Services Digital Network Signaling Gateway Down alarm, refer to 

“Integrated Services 

Digital Network Signaling Gateway Down—Signaling (156)” section on page 10-157

.

Integrated Services Digital Network Signaling Gateway Inactive—Signaling 
(157)

The Integrated Services Digital Network Signaling Gateway Inactive alarm (major) indicates that a 

shutdown

 command has been executed in the application server on the ISDN gateway side. To 

troubleshoot and correct the cause of the Integrated Services Digital Network Signaling Gateway 
Inactive alarm, refer to 

“Integrated Services Digital Network Signaling Gateway Inactive—Signaling 

(157)” section on page 10-157

.

Invalid Integrated Services Digital Network Interface 
Identification—Signaling (158)

The Invalid Integrated Services Digital Network Interface Identification event serves as a warning that 
an interface ID is not configured correctly on the ISDN gateway side. To correct the cause of the event, 
configure the D-channel correctly on the gateway side. The D-channel configuration on the call-agent 
side should match with that on the gateway side.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды