manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 431

 

10-63

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 10      Signaling Troubleshooting

Signaling Events and Alarms

SIGNALING (114)

To troubleshoot and correct the cause of the alarm, refer to the 

“Signaling Gateway Process Is 

Out-of-Service—Signaling (114)” section on page 10-152

.

Note

When a port on a ITP is removed from service using the 

shut

 command, multiple Signaling 113 and 114 

alarms are raised (ON status). When the port is recovered by cycling the ITP power, all alarms raised 
are cleared (OFF status) and are removed from CURRENT_ALARM table. However, not all cleared 
alarms (OFF status) are displayed on the subscriber terminal. Only the first instance of the cleared alarms 
(OFF status) with a variation in TYPE, NUMBER, and COMPONENT-ID 

are

 displayed. Multiple 

instances of the cleared alarms (OFF status) where the TYPE, NUMBER, and COMPONENT-ID are 
identical 

are not

 displayed.

SIGNALING (115)

To monitor and correct the cause of the event, refer to the 

“Invalid Routing Context Received—Signaling 

(115)” section on page 10-115

.

DESCRIPTION

Signaling Gateway Process is Out-of-Service

SEVERITY

MAJOR

THRESHOLD

100

THROTTLE

0

DATAWORDS

Signaling Gateway–STRING [17]

PRIMARY

 

CAUSE

All of the SCTP associations between the SGP and the CA are out-of-service.

PRIMARY

 

ACTION

See the SCTP association alarm definition to determine how to rectify the problem.

SECONDARY

 

CAUSE

The M3UA layer is down between the CA and the SGP.

SECONDARY

 

ACTION

Use the Cisco snooper utility to determine why M3UA layer is down. Also see the log for additional 
information.

DESCRIPTION

Invalid Routing Context Received

SEVERITY

WARNING

THRESHOLD

100

THROTTLE

0

DATAWORDS

Invalid Routing Cont–FOUR_BYTES

 

SG from Which the In–STRING [17]

PRIMARY

 

CAUSE

The routing context was configured improperly on the CA or the signaling gateway (SG).

PRIMARY

 

ACTION

Reconfigure the routing context on the CA or the SG so that it matches in both places.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды