manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Поделиться
Скачать
Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 352

 

8-8

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 8      Operations Support System Troubleshooting

Operations Support System Events and Alarms

OSS (14)

To troubleshoot and correct the cause of the alarm, refer to the 

“User Session Count Exceeds Major 

Threshold Limit—Operations Support System (14)” section on page 8-15

.

OSS (15)

OSS (15) is not used. It is reserved for future use.

OSS (16)

To for additional information, refer to the 

“Session Has Been Removed by Session Control Policy 

—Operation Support System (16)” section on page 8-12

.

DESCRIPTION

User Session Count Exceeds Major Threshold Limit

SEVERITY

MAJOR

THRESHOLD

100

THROTTLE

0

DATAWORDS

Session Type - STRING [16]

 

Session Maximum Limit - STRING [3]

 

Session Current Usage - STRING [3]

 

Session Usage Percentage - STRING [3]

PRIMARY

 

CAUSE

The user session usage has reached maximum allowed limit.

PRIMARY

 

ACTION

Use the 

report client_session

 command to view all login sessions. Use the 

stop client_session

 

command to remove stale sessions.

DESCRIPTION

Session Has Been Removed by Session Control Policy

SEVERITY

INFO

THRESHOLD

100

THROTTLE

0

DATAWORDS

Policy ID - STRING [64]

 

Session Type - STRING [16]

 

User ID - STRING [16]

 

Session Key - STRING [20]

PRIMARY

 

CAUSE

Session has been removed by the session control policy.

PRIMARY

 

ACTION

This is an informational alert and no corrective action is necessary.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды