Cisco BTS 10200 Softswitch Скачать руководство пользователя страница 129

Страница: 129 / 874

3-23

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 3 Billing Troubleshooting

Billing Events and Alarms

BILLING (54)

To troubleshoot and correct the cause of the alarm, refer to the

“Event Message Disk Space 70 Percent

Full—Billing (54)” section on page 3-42

BILLING (55)

To troubleshoot and correct the cause of the alarm, refer to the

“Event Message Disk Space 100 Percent

Full—Billing (55)” section on page 3-42

DESCRIPTION

Event Message Disk Space 70 Percent Full

SEVERITY

MAJOR

THRESHOLD

100

THROTTLE

DATAWORDS

Number of Megabytes Used for Eve–FOUR_BYTES

Directory Containing Event Messa–STRING [30]

Location Tag–STRING [30]

PRIMARY

CAUSE

The event message storage has reached 70% of the maximum storage allowed.

PRIMARY

ACTION

Move the event message files out of the specified directory. Store them in another location, or discard
them.

DESCRIPTION

Event Message Disk Space 100 Percent Full

SEVERITY

CRITICAL

THRESHOLD

100

THROTTLE

DATAWORDS

Number of Megabytes Used for Eve–FOUR_BYTES

Directory Containing Event Messa–STRING [30]

Location Tag–STRING [30]

PRIMARY

CAUSE

The event message storage has been completely filled. No additional event messages will be written
to disk until more space is made available.

PRIMARY

ACTION

Move the event message files out of the specified directory. Store them in another location, or discard
them.

Содержание BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание BTS 10200 Softswitch

Отзывы:

Бренды по названию

Популярные бренды

Cisco BTS 10200 Softswitch, Руководство по устранению неисправностей

Результаты поиска

Содержание BTS 10200 Softswitch

Отзывы:

Бренды по названию

Популярные бренды