Cisco ASR 920-24SZ-IM Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 54

background image

Figure 32: Removing a SFP Module without Bale-Clasp Latch From Cisco ASR 920-24SZ-IM, ASR-920-24SZ-M, ASR-920-24TZ-M Router

SFP module without Bale-Clasp Latch—Use the extraction tool to remove the SFP by inserting the tool into
the side of the SFP module and pulling it out of the module as shown in the figure below.

Step 4

Grasp the SFP module between your thumb and index finger, and carefully remove it from the module slot.

Step 5

For fiber-optic SFP modules, insert a dust plug into the optical ports of the SFP module to keep the optical
interfaces clean.

Step 6

Place the removed SFP module in an antistatic bag or other protective environment.

Connecting to the 10/100/1000 Ports

The router 10/100/1000 ports configure themselves to operate at the speed of attached devices. If the attached
ports do not support autonegotiation, you can explicitly set the speed and duplex parameters. Connecting
devices that do not autonegotiate or that have their speed and duplex parameters manually set can reduce
performance or result in no linkage.

Note

To maximize performance, choose one of these methods for configuring the Ethernet ports:

• Let the ports autonegotiate both speed and duplex.
• Set the port speed and duplex parameters on both ends of the connection.

Procedure

Step 1

When connecting to workstations, servers, and routers, connect a straight-through cable to an RJ-45 connector
on the front panel.When connecting to routers or repeaters, use a crossover cable.

You can use the

mdix auto

interface configuration command in the CLI to enable the automatic

medium-dependent interface crossover (auto-MDIX) feature. When the auto-MDIX feature is
enabled, the router detects the required cable type for copper Ethernet connections and configures
the interfaces accordingly. Therefore, you can use either a crossover or a straight-through cable for
connections to a copper 10/100/1000, or an SFP module port on the router, regardless of the type
of device on the other end of the connection.

Note

Installing the Router

38

Installing the Router

Connecting to the 10/100/1000 Ports

«
...
36
37
38
39
40
...
»

Содержание ASR 920-24SZ-IM























































Отзывы:

Нет отзывов

Похожие инструкции для ASR 920-24SZ-IM

Бренд: Panasonic Страницы: 2

Бренд: Cambium Networks Страницы: 29

Бренд: QNAP Страницы: 20

Бренд: Vanguard Страницы: 4

Azure StorSimple 8100

Бренд: Microsoft Страницы: 12

Бренд: Conceptronic Страницы: 2

Бренд: ZyXEL Communications Страницы: 2

Бренд: Lanner Страницы: 63

Turbo NAS TVS-71 Series

Бренд: QNAP Страницы: 51

Бренд: Juniper Страницы: 420

Бренд: Zhone Страницы: 53

Network Adapter ADZIFCF

Бренд: Addonics Technologies Страницы: 1

Бренд: Juniper Страницы: 396

GS2020E GigaSPIRE BLAST

Бренд: Calix Страницы: 15

Бренд: Vaisala Страницы: 32

Бренд: Lanpro Страницы: 3

Бренд: Jensen of Scandinavia Страницы: 2

Temporary Target Board M38517T-ADS

Бренд: Renesas Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды