Cisco ASR 907 Скачать руководство пользователя страница 97

Страница: 97 / 204

Figure 53: Power Supply with Lead Wires

Positive (+) lead wire

2,
4

Negative (-) lead wire

1,
3

Do not overtorque the fasteners of the terminal block. The recommended maximum torque is from
25 in.-lb (2.82 N-m).

Caution

Step 6

Use a tie wrap to secure the wires to the rack, so that the wires are not pulled from the terminal block by casual
contact. Make sure the tie wrap allows for some slack in the wire.

Activating the DC Power Supply

Perform the following procedure to activate the DC power supply:

Procedure

Step 1

Remove the tape from the circuit-breaker switch handle, and restore power by moving the circuit-breaker
switch handle to the On (|) position.

Step 2

Verify power supply operation by checking if the power supply front panel LEDs are in the following states:

• INPUT OK LED is green
• OUTPUT FAIL LED is green

Cisco ASR 907 Router Hardware Installation Guide

Installing the Cisco ASR 907 Router

Activating the DC Power Supply

Содержание ASR 907












































































































































































































Результаты поиска

Содержание ASR 907

Отзывы:

Похожие инструкции для ASR 907

Бренды по названию

Популярные бренды

Cisco ASR 907, Руководство по установке оборудования

Результаты поиска

Содержание ASR 907

Отзывы:

Похожие инструкции для ASR 907

Бренды по названию

Популярные бренды