manualshive.com logo in svg

Cisco ASR 907, Руководство по установке оборудования

Cisco ASR 907 - высокопроизводительный маршрутизатор для сетей передачи данных. Установите оборудование сами, используя "Hardware Installation Manual", который можно скачать совершенно бесплатно с нашего сайта. Повысьте эффективность сети с Cisco ASR 907. (website).

Поделиться
Скачать
background image

Comment

Indication

STAT LED
State

PWR LED
State

System is up with ROMMON. Both the
FPGA image is validated successfully, but
the booted ROMMON (primary or
secondary) is undetermined.

FPGA configured and core validated
successfully.

FPGA image passed the control to
micro-loader to boot ROMMON.

Off

Flashing
Light
Green and
Green
alternatively

System is up with ROMMON. FPGA
image is validated successfully, but the
booted ROMMON (primary or secondary)
is undetermined.

The digital code signing functionality
reported upgrade FPGA image
validation error and is continuing with
the FPGA image.

Amber

FPGA is up but both primary and
secondary ROMMON failed. System is in
hung state.

The digital code signing functionality
reported failure in the ROMMON
image validation.

Red

IOS writes into FPGA register to indicate
that it has booted, FPGA stops flashing
PWR LED and turns Green. Software now
controls the STAT LED.

IOS is successfully booted

Off

Green

Interface Module LEDs

The LED summary applies to the following interface modules:

• SFP Gigabit Ethernet Interface Module
• RJ45 Gigabit Ethernet Interface Module
• XFP 10 Gigabit Ethernet XFP Interface Module
• 8x1 Gigabit Ethernet SFP + 1x10 Gigabit Ethernet SFP+ Interface Module
• 8x1 Gigabit Ethernet RJ45 + 1x10 Gigabit Ethernet SFP+ Interface Module
• 2x10 Gigabit Ethernet SFP+ Interface Module
• 48 T1/E1 TDM Interface Module (48XT1/E1)
• 48 T3/E3 TDM Interface Module (48XT3/E3)
• 1-port OC-192 or 8-port Low Rate CEM Interface Module
• 8/16-port 1 Gigabit Ethernet (SFP/SFP) + 1-port 10 Gigabit Ethernet (SFP+) / 2-port 1 Gigabit Ethernet

(CSFP) Interface Module

The Status LED is Amber for the 10 Gigabit Ethernet ports when operating in WAN mode for the following
IMS:

• 8x1 Gigabit Ethernet SFP + 1x10 Gigabit Ethernet SFP+ Interface Module
• 8x1 Gigabit Ethernet RJ45 + 1x10 Gigabit Ethernet SFP+ Interface Module
• 2x10 Gigabit Ethernet SFP+ Interface Module

Cisco ASR 907 Router Hardware Installation Guide

183

Troubleshooting

Interface Module LEDs

Содержание ASR 907













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 907

Cabletron Systems MMAC-5FNB Overview And Setup Manual preview
MMAC-5FNB
Бренд: Cabletron Systems Страницы: 21
LaCie 8BIG RACK THUNDERBOLT 2 Quick Start Manual preview
8BIG RACK THUNDERBOLT 2
Бренд: LaCie Страницы: 28
Vivotek FE9181-H Quick Installation Manual preview
FE9181-H
Бренд: Vivotek Страницы: 170
ZyXEL Communications P-336M Quick Start Manual preview
P-336M
Бренд: ZyXEL Communications Страницы: 125
EnGenius ETR9360 Quick Start Manual preview
ETR9360
Бренд: EnGenius Страницы: 3
Cyclades AlterPath Manager 2500 Installation, Configuration And User Manual preview
AlterPath Manager 2500
Бренд: Cyclades Страницы: 368
TP-Link Archer C7 How To Set Up preview
Archer C7
Бренд: TP-Link Страницы: 4
Ryobi RE180PL1 Operator'S Manual preview
RE180PL1
Бренд: Ryobi Страницы: 44
Patton electronics 3224 Diamond Edge Specification Sheet preview
3224 Diamond Edge
Бренд: Patton electronics Страницы: 2
NETGEAR FS305 Installation Manual preview
FS305
Бренд: NETGEAR Страницы: 2
Comtrend Corporation CT-510 User Manual preview
CT-510
Бренд: Comtrend Corporation Страницы: 69
Atlantis Land A02-RA243-W54M Quick Start Manual preview
A02-RA243-W54M
Бренд: Atlantis Land Страницы: 85
Kraun 1T1R - USB User Manual preview
1T1R - USB
Бренд: Kraun Страницы: 32
IBM IBM 9077 Get Connected preview
IBM 9077
Бренд: IBM Страницы: 342
D-Link N300 User Manual preview
N300
Бренд: D-Link Страницы: 236
Zte Z1320 User Manual preview
Z1320
Бренд: Zte Страницы: 11
QNAP TS-451DeU User Manual preview
TS-451DeU
Бренд: QNAP Страницы: 49
Quintum Tenor AXT1600 Release Note preview
Tenor AXT1600
Бренд: Quintum Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды