Cisco ASR 907 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 204

background image

• External management interfaces (RS232 console, management ENET, USB console, USB storage) and

system status LED indicators

Supported RSPs

Effective Cisco IOS-XE Release 3.16, the Cisco ASR 907 Router supports the following RSP:

• A900-RSP3C-400-W—Provides 8 GB of SDRAM, 20 Mb of TCAM memory on every ASIC.

The RSP does not provide external network interfaces for user traffic. All network interfaces are provided
through separate IMs.

Supported RSP Features

The RSP provides the following features on the Cisco router:

• Centralized data plane, timing, and control plane functions for the system
• High-level control of interface modules
• Management functionalities for the router
• Control plane (host) CPU and associated memory in which IOS-XE and platform control software runs
• Nonvolatile memory for storage of software images, configurations, and system files
• Enabling and monitoring the health and presence of fan trays, interface modules, and power supplies
• Field replacement and hot-swap capabilities

Swapping of Interface Modules

The following Ethernet interface modules support swapping on the Cisco A900-RSP3C-400-W module.

• 8-port Gigabit Ethernet SFP Interface Module (8X1GE)

• 8-port Gigabit Ethernet RJ45 (Copper) Interface Module (8X1GE)

• SFP Combo IM—8-port Gigabit Ethernet (8X1GE) + 1-port 10 Gigabit Ethernet (1X10GE)

• Copper Combo IM—8-port Gigabit Ethernet (8X1GE) + 1-port 10 Gigabit Ethernet Interface

Module(1X10GE)

• 2-port 10 Gigabit Ethernet Interface Module (2X10GE)

• 2-port 40 Gigabit Ethernet Interface Module (2X40GE)

• 1-port 100 Gigabit Ethernet Interface Module (1X100GE)

• 2-port 100 Gigabit Ethernet (QSFP) Interface Module (2X100GE)

• 1-Port OC-192 or 8-Port Low Rate CEM Interface Module

• 48 T1/E1 TDM Interface Module (48XT1/E1)

• 48 T3/E3 TDM Interface Module (48XT3/E3)

Use the

hw-module subslot default

command before performing a swap of the modules. to default the

interfaces on the interface module.

The

hw-module subslot default

command is

not

supported on the TDM and OC-3 interface modules.

Note

Cisco ASR 907 Router Hardware Installation Guide

8

Cisco ASR 907 Router Overview

Supported RSPs

«
...
16
17
18
19
20
...
»

Содержание ASR 907













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 907

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 32

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 8

Бренд: Ubiquiti Страницы: 23

Бренд: CELOT Страницы: 34

InnoMedia MTA 3328-2R

Бренд: VoiceLine Страницы: 18

SW-UNM-24FE2GC-24POE

Бренд: Morrell Страницы: 8

Бренд: Patton electronics Страницы: 2

Бренд: NetBurner Страницы: 30

Barricade SMC7908VoWBRA2

Бренд: SMC Networks Страницы: 2

Бренд: UltrArmor Страницы: 3

Бренд: UfiSpace Страницы: 34

Бренд: ubiquoss Страницы: 46

Y.FORCE YTPC400

Бренд: YTTEK Страницы: 26

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 8

AirProtect Enterprise Engine 6100

Бренд: 3Com Страницы: 12

Бренд: 2Wire Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды