background image

delay clear

To configure the amount of time before a Synchronous Transport Signal (STS) path delay trigger alarm is
cleared, use the

delay clear

command in STS path configuration mode. To return the command to its default

setting, use the

no

form of this command.

delay clear value

no delay clear value

Syntax Description

Value, in milliseconds, before an STS path delay trigger alarm is cleared. The range is
from 0 to 180000. The default is 10 seconds.

value

Command Default

The default is 10 seconds.

Command Modes

STS path configuration

Command History

Modification

Release

This command was introduced.

Release 3.9.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

Task ID

Operations

Task ID

read, write

sonet-sdh

Examples

The following example shows how to specify that STS path delay trigger alarms should be cleared after 7000
milliseconds:

RP/0/RSP0/CPU0:router(config)#

controller sonet 0/2/0/3

RP/0/RSP0/CPU0:router(config-sonet)#

sts 1

RP/0/RSP0/CPU0:router(config-stsPath)#

delay clear 7000

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x    

859

SONET Controller Commands on the Cisco ASR 9000 Series Router

delay clear

Содержание ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы: