manualshive.com logo in svg

Cisco ASR 9000 Series, Справочник по командам

Поделиться
Скачать
Cisco ASR 9000 Series Скачать руководство пользователя страница 608

hw-module load-balance bundle l2-service l3-params

Effective with Cisco IOS XR Release 4.0.1, the

hw-module load-balance bundle l2-service l3-params

command is replaced by the

load-balancing flow

L2VPN configuration command. See the

load-balancing

flow

command in the

Cisco ASR 9000 Series Aggregation Services Router L2VPN and Ethernet Services

Command Reference

for more information.

Note

To configure load balancing for L2 services using L3 parameters, use the

hw-module load-balance bundle

l2-service l3-params

command in global configuration mode. To disable load balance L2 services, use the

no form of this command.

hw-module load-balance bundle l2-service l3-params

no hw-module load-balance bundle l2-service l3-params

Syntax Description

This command has no keywords or arguments.

Command Default

No default behavior or values

Command Modes

Global configuration

Command History

Modification

Release

This command was introduced.

Release 3.9.1

This command was replaced by the

load-balancing flow

command.

Release 4.0.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

This command enables the L2 service-specific load-balancing for bundle Ethernet Flow Points (EFPs). By
default, bundle load-balancing is done based on the MAC SA/DA fields in the packet header. When L2
service-specific load-balancing is configured, all traffic egressing bundle EFPs are load-balanced based on
the IPv4 source and destination addresses in the packet. If the packet does not have IPv4 addresses, the default
load-balancing is used.

Task ID

Operations

Task ID

read, write

root-lr

   Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

588

Link Bundling Commands on the Cisco ASR 9000 Series Router

hw-module load-balance bundle l2-service l3-params

Содержание ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды