manualshive.com logo in svg

Cisco ASR 9000 Series, Справочник по командам

Поделиться
Скачать
Cisco ASR 9000 Series Скачать руководство пользователя страница 46

loopback (DWDM)

To configure the DWDM controller for loopback mode, use the

loopback

command in DWDM configuration

mode. To remove the loopback DWDM command from the configuration file, use the

no

form of this command.

loopback

{

internal| line

}

no loopback

{

internal| line

}

Syntax Description

Specifies that all the packets be looped back to the router.

internal

Specifies that the incoming network packets be looped back to the DWDM
network.

line

Command Default

This command is disabled by default.

Command Modes

DWDM configuration

Command History

Modification

Release

This command was introduced.

Release 3.9.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

The DWDM controller supports two loopback operation modes for diagnostic purposes: internal and line.
The terminal (internal) loopback mode allows the received data from the Layer 2 Framer (for example, a
SONET/SDH framer for POS or Ethernet MAC for 10GE) of the PLIM to be looped back to the ingress side
of the Framer. This allows the packets to be looped back to the PLIM. The line loopback mode allows the
received trunk/DWDM line Rx to be connected to the trunk/DWDM line Tx towards the line. This is used
for line diagnostics.

Task ID

Operations

Task ID

read, write

dwdm

   Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

26

Dense Wavelength Division Multiplexing Commands on the Cisco ASR 9000 Series Router

loopback (DWDM)

Содержание ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды