Cisco ASR 9000 Series Скачать руководство пользователя | Manualshive

Страница: 223 / 1138

background image

efd

To enable Ethernet Fault Detection (EFD) on all down Maintenance End Points (MEPs) in a down MEPs
service, use the

efd

command in CFM domain service configuration mode. To disable EFD, use the no form

of this command.

efd

{

protection-switching

}

no efd

Syntax Description

Enables protection switching, which causes high-priority notifications to be sent when
peer MEPs specified for cross-check time out, or when CCMs are received with the
RDI bit set.

The high-priority notifications only apply to MEPs that are offloaded. In the
case of non-offloaded MEPs, enabling protection switching has no effect,
and the command only enables EFD.

Note

protection-switching

Command Default

EFD is disabled.

Command Modes

CFM domain service configuration (config-cfm-dmn-svc)

Command History

Modification

Release

This command was introduced.

Release 3.9.1

The

protection-switching

keyword was included.

Release 4.3.1

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

EFD can only be enabled for down MEPs within a down MEPs service.

If the

efd

command is issued when any MEP in the service has any of the following error conditions, the MEP

will shut down the interface:

•

The MEP appears cross-connected to another MAID.

•

The MEP is receiving invalid CCMs, such as receiving its own MAC or MEP-ID.

•

All peer MEPs are reporting a state other than UP via the Port Status TLV.

•

A peer MEP is reporting a state other than UP in Interface Status TLV.

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

203

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

efd

«
...
221
222
223
224
225
...
»

Содержание ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 9000 Series

Бренд: 3onedata Страницы: 4

Бренд: Doepke Страницы: 44

IP Solutions PagePro VIP-204

Бренд: Valcom Страницы: 4

Бренд: Samson Страницы: 72

Бренд: ICC Страницы: 58

Бренд: ICC Страницы: 70

AirLink RV50 Series

Бренд: Sierra Wireless Страницы: 78

Бренд: ActionTec Страницы: 2

CentrePoint Data Hub

Бренд: ActiGraph Страницы: 14

Бренд: ECKELMANN Страницы: 58

Бренд: Comcast Страницы: 6

Бренд: Comcast Страницы: 13

Бренд: ZyXEL Communications Страницы: 2

Бренд: ZyXEL Communications Страницы: 2

Бренд: ZyXEL Communications Страницы: 2

Бренд: ActionTec Страницы: 2

Бренд: FreePP Страницы: 80

Бренд: GL-INET Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды