Cisco ASR 9000 Series Скачать руководство пользователя | Manualshive

Страница: 1045 / 1138

background image

loopback (T3/E3)

To loop the entire T3 or E3 line (all 28 T1 channels or all 21 E1 channels) on the T3 controller or E3 controller,
use the

loopback

command in T3 or E3 configuration mode. To remove the loop, use the

no

form of this

command.

loopback

{

local

| {

network

|

remote

{

line| payload

}}}

no loopback

Syntax Description

Loops the data back toward the router and sends an alarm indication signal (AIS)
out toward the network.

local

Sets the loopback toward the network before going through the framer (

line

) or

after going through the framer (

payload

).

network

{

line

|

payload

}

Sends a far-end alarm control (FEAC) request to the remote end requesting that
it enter into a network line loopback. FEAC requests (and therefore remote
loopbacks) are possible only when the T3 is configured for C-bit framing. The
M23 format does not support remote loopbacks.

remote

{

line

|

payload

}

Command Default

No loops are configured on the T3 line.

Command Modes

T3 configuration

E3 configuration

Command History

This command was introduced.

Release 3.9.0

Support for E3 configuration was added.

Release 4.0.0

Usage Guidelines

Use the

loopback

command for troubleshooting purposes. To verify that a loopback is configured on the

interface, use the

show controllers t3

or

show controllers e3

command in EXEC mode. Note that remote

loopback is valid only in C-bit parity mode.

You can also loopback each T1 or E1 channel by using the

loopback

command in T1 or E1 configuration

mode.

Task ID

Operations

Task ID

read, write

sonet-sdh

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

1025

T3, E3, T1, E1 Controller Commands on the Cisco ASR 9000 Series Router

loopback (T3/E3)

«
...
1043
1044
1045
1046
1047
...
»

Содержание ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 9000 Series

Бренд: RTA Страницы: 80

Бренд: DAUDIN Страницы: 24

Бренд: Cisco Страницы: 76

Бренд: Motorola Страницы: 28

Бренд: Motorola Страницы: 351

SURFboard eXtreme SBG6782-AC

Бренд: Motorola Страницы: 2

Бренд: Far south networks Страницы: 211

Бренд: QNAP Страницы: 168

Бренд: Realm Страницы: 8

MGate 5118 Series

Бренд: Moxa Technologies Страницы: 8

FieldGate SWG50

Бренд: Endress+Hauser Страницы: 48

1-Wire Gateway 20 Modbus TCP

Бренд: esera automation Страницы: 10

Бренд: Philio Technology Corporation Страницы: 40

Бренд: D-Link Страницы: 19

Бренд: Agilent Technologies Страницы: 157

Бренд: IAI Страницы: 188

Бренд: Yeastar Technology Страницы: 87

iSeeVideo ISEE-SCHGW

Бренд: NAPCO Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды