Cisco ASR 14000 Series Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 132

background image

5

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Installation Guide

OL-16973-01

Preface

Note

Means

reader take note

. Notes contain helpful suggestions or references to materials not contained in

this manual.

Timesaver

Means

the described action saves time

. You can save time by performing the action described in the

paragraph.

Warning

This warning symbol means

danger

. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. To see translations of the warnings that appear in
this publication, refer to the

Regulatory Compliance and Safety Information

document that

accompanied this device.

Statement 1074

Related Documentation

For complete information on the ASR 14000 series 8-slot line card chassis, see the following
publications:

•

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Installation Guide

•

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Site Planning Guide

•

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Unpacking, Mounting, and Securing
Guide

•

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis System Description

•

Cisco ASR 14000 Series Router SIP and SPA Hardware Installation Guide

•

Regulatory Compliance and Safety Information for the Cisco ASR14000 Series Aggregation
Services Router

•

Cisco ASR 14000 Series Router Documentation Roadmap

•

About Cisco IOS XR Software Documentation

See the

“Obtaining Documentation, Obtaining Support, and Security Guidelines” section on page 6

information on obtaining these and other publications.

For a complete listing of available software documentation for the Cisco ASR 14000 series 8-slot line
card chassis, see the About Cisco IOS XR Software Documentation, available online at:

http://www.cisco.com/en/US/products/ps5845/index.html

Then check the links under “Technical Documentation & Tools.”

«
...
7
8
9
10
11
...
»

Содержание ASR 14000 Series





































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 14000 Series

ShareCenter DNS-320L

Бренд: D-Link Страницы: 4

Бренд: H3C Страницы: 22

Бренд: H3C Страницы: 3

Бренд: Ubiquiti Страницы: 22

UniFi UAP-AC-LR

Бренд: Ubiquiti Страницы: 28

Бренд: Draytek Страницы: 8

Бренд: TP-Link Страницы: 3

Nighthawk M6 Pro

Бренд: AT&T Страницы: 2

Бренд: ZyXEL Communications Страницы: 299

Бренд: UHP Страницы: 15

Бренд: Ubiquiti Страницы: 21

Бренд: MiWire Страницы: 24

Бренд: Xantech Страницы: 16

Бренд: EMC Страницы: 88

Бренд: ZyXEL Communications Страницы: 191

SmartNode 4634 Series

Бренд: Patton electronics Страницы: 12

Бренд: TP-Link Страницы: 2

Бренд: ICP DAS USA Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды