Cisco ASR 14000 Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 132

Cisco ASR 14000 Series Скачать руководство пользователя страница 33

2-11

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Installation Guide

OL-16973-01

Chapter 2 Installing and Removing Power Components

How to Install or Remove the Power Components

Are there comparable ASR 14000 parts and product numbers?

–

AC Wye PDU Cisco product number ASR14K/8-ACW-KIT=

–

AC Delta PDU Cisco product number ASR14K/8-ACD-KIT=

–

DC PDU Cisco product number ASR14K/8-DC-KIT=

Steps

To install a PDU, follow these steps:

Step 1

Attach the ESD-preventive wrist strap to your wrist and connect its leash to one of the ESD connection
sockets on the rear (MSC) side of the chassis or a bare metal surface on the chassis.

Step 2

Make sure that the PDU is unplugged.

Step 3

Grasp the PDU by the side and set it carefully into place in a PDU slot on the rear (MSC) side of the
chassis. Be sure to lift the PDU over the lip on the edge of the chassis, and align the guide pins on the
chassis with the guide holes on the PDU.

Caution

Do not lift the PDU by the power cord—doing so can damage the PDU or the cord.

Step 4

If needed, put the second PDU into place in the other PDU slot on the chassis.

Note

The PDU holding plate bolts to both PDUs and the side of the interior of the chassis.

Step 5

Install the PDU holding plate.

a.

Slide the holding plate into place on top of the PDU, using the guide bolts on the side of the chassis
to place it correctly.

b.

Use the socket wrench to bolt the holding plate to the top of the PDUs with the eight 10-mm bolts
(four for each PDU).

c.

Use the socket wrench to bolt the holding plate to the interior of the side of the chassis with the four
8-mm bolts (two for each side)

Step 6

Use the socket wrench to install the 8-mm center holding bolt and the 10-mm nut.

What to Do Next

After performing this task, install the power modules (see the

“Installing a Power Module” section on

), and replace any cosmetic covers.

Removing a PDU

This section describes how to remove a PDU in the Cisco ASR 14000 series 8-slot line card chassis. For
information on the difference between the power types, see the

“DC Power Systems” section on page 2-4

and the

“AC Power Systems” section on page 2-8

. For complete information on regulatory compliance

and safety, see

Regulatory Compliance and Safety Information for the Cisco ASR14000 Series

Aggregation Services Router

.

«
...
31
32
33
34
35
...
»

Содержание ASR 14000 Series





































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды