manualshive.com logo in svg

Cisco ASR 1001-X, Руководство по установке оборудования, Страница: 47 / 152

Поделиться
Скачать
Cisco ASR 1001-X Скачать руководство пользователя страница 47

Guidelines for 23-in. (Telco) Racks

If needed, you can also install the Cisco ASR 1001-X Router in 23-in. (Telco) racks. For information on the
adapters needed for 23 in. racks, contact the Newton Instrument Company:

http://www.enewton.com

111 East A Street, Butner NC, USA, 27509

919 575-6426

Equipment Rack Guidelines

The placement of racks can affect personnel safety, system maintenance, and the system

’

s ability to operate

within the environmental characteristics described in the above tables. Choose a proper location for the Cisco
ASR 1001-X Router by following the guidelines below.

Locating for Safety

If the Cisco ASR 1001-X Router is the heaviest or the only piece of equipment in the rack, consider installing
it at or near the bottom to ensure that the rack

’

s center of gravity is as low as possible.

For additional information about the proper placement of electronic equipment, see the document GR-63-CORE,
Network Equipment Building System (NEBS) Requirements: Physical Protection.

Locating for Easy Maintenance

Keep at least 3 feet of clear space in front of and behind the rack. This space ensures that you can remove the
Cisco ASR 1001-X Router components and perform routine maintenance and upgrades easily.

Avoid installing the Cisco ASR 1001-X Router in a congested rack and consider how the routing of cables
from other pieces of equipment in the same rack might affect access to the routers cards.

The front and top of the chassis must remain unobstructed to ensure adequate airflow and prevent overheating
inside the chassis.

Allow the following clearances for normal system maintenance:

•

At the top of the chassis

—

At least 3 in. (7.6 cm)

•

In front of the chassis

—

3 to 4 ft (91.44 cm to 121.92 cm)

To avoid problems during installation and ongoing operation, follow these general precautions when you plan
the equipment locations and connections:

•

Use the

show environment all

and the

show facility-alarm status

command regularly to check the

internal system status. The environmental monitor continually checks the interior chassis environment;
it provides warnings for high temperature and creates reports on any occurrences. If warning messages
are displayed, take immediate action to identify the cause and correct the problem. For more information
on these commands, see the

“

Environmental Monitoring and Reporting Functions

”

section on page 5-15

.

•

Keep the Cisco ASR 1001-X Router off the floor and out of the areas that collect dust.

Cisco ASR 1001-X Router Hardware Installation Guide    

39

Preparing Your Site for Installation

Rack-Mounting Guidelines

Содержание ASR 1001-X

























































































































































Отзывы:

Нет отзывов