Cisco aironet 1130 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 184

background image

64

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Connecting the Cisco 1520 Series Mesh Access Point to Your Network

Figure 41

Global Configuration Window

Note

The fast heartbeat timer is not supported on mesh access points.

Step 2

In the AP Primary Discovery Timeout field, enter a value between 30 and 3600 seconds (inclusive) to
configure the access point primary discovery request timer. The default value is 120 seconds.

Step 3

If you want to specify a primary backup controller for all access points, enter the IP address of the
primary backup controller in the Back-up Primary Controller IP Address field and the name of the
controller in the Back-up Primary Controller Name field.

Note

The default value for the IP address is 0.0.0.0, which disables the primary backup controller.

Step 4

If you want to specify a secondary backup controller for all access points, enter the IP address of the
secondary backup controller in the Back-up Secondary Controller IP Address field and the name of the
controller in the Back-up Secondary Controller Name field.

Note

The default value for the IP address is 0.0.0.0, which disables the secondary backup controller.

Step 5

Click

Apply

to commit your changes.

Step 6

If you want to configure primary, secondary, and tertiary backup controllers for a specific point, follow
these steps:

a.

Click

Access Points

>

All APs

to open the All APs window.

b.

Click the name of the access point for which you want to configure primary, secondary, and tertiary
backup controllers.

«
...
62
63
64
65
66
...
»

Содержание aironet 1130

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для aironet 1130

Бренд: TC Electronic Страницы: 2

Бренд: Abocom Страницы: 11

Бренд: Abocom Страницы: 19

Бренд: XESS Страницы: 23

Бренд: Juniper Страницы: 502

Protege PRT-PX16-PCB

Бренд: ICT Страницы: 34

ADSL 2/2+ VPN Firewall Router ADE-4300A/B

Бренд: Planet Страницы: 132

Бренд: Waves Страницы: 41

Бренд: Multitech Страницы: 81

Бренд: Z-Com Страницы: 18

Бренд: MICROENER Страницы: 24

Бренд: Enterasys Страницы: 62

Imagestore Intuition+

Бренд: Miranda Страницы: 60

ULTRIX-FM-NS-1RU

Бренд: Ross Страницы: 5

Бренд: Teltonika Страницы: 12

Бренд: ZALMAN Страницы: 12

Бренд: Sony Ericsson Страницы: 2

Бренд: LevelOne Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды