Cisco aironet 1130 Скачать руководство пользователя страница 177 | Manualshive

Страница: 177 / 184

background image

177

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Adding and Managing Mesh Access Points with Cisco WCS

•

An amber dot represents an acceptable SNR (20-25 dB).

•

A red dot represents a low SNR (below 20 dB).

•

A black dot indicates a root access point.

Using Mesh Filters to Modify Map Display of Maps and Mesh Links

In the mesh hierarchical window, you can also define mesh filters to determine which mesh access points
display on the map based on hop values as well as what labels display for mesh links.

Mesh access points are filtered by the number of hops between them and their root access point.

To use mesh filtering, follow these steps.

Step 1

To modify what label and color displays for a mesh link, follow these steps:

a.

In the Mesh Parent-Child Hierarchical View, select an option from the Link Label drop-down
menu. Options are None, Link SNR, and Packet Error Rate.

b.

In the Mesh Parent-Child Hierarchical View, select an option from the Link Color drop-down
menu to define which parameter (Link SNR or Packet Error Rate) determines the color of the
mesh link on the map.

Note

The color of the link provides a quick reference point of the SNR strength or Packet Error Rate.

Table 28

Bridging Link Information

Parameter

Description

Information fetched on

Date and time that information was compiled.

Link SNR

Link signal-to-noise ratio (SNR).

Link Type

Hierarchical link relationship.

SNR Up

Signal-to-noise radio for the uplink (dB).

SNR Down

Signal-to-noise radio for the downlink (dB).

PER

The packet error rate for the link.

Tx Parent Packets

The TX packets to a node while acting as a parent.

Rx Parent Packets

The RX packets to a node while acting as a parent.

Time of Last Hello

Date and time of last hello.

Table 29

Definition for SNR and Packet Error Rate Link Color

Link Color

Link SNR

Packet Error Rate (PER)

Green

Represents a SNR above 25 dB (high
value)

Represents a PER of one percent (1%) or
lower

«
...
175
176
177
178
179
...
»

Содержание aironet 1130

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для aironet 1130

Бренд: ABB Страницы: 66

Бренд: Maco Страницы: 38

Бренд: Parkside Страницы: 55

Бренд: Parkside Страницы: 34

Бренд: RadiSys Страницы: 44

F-ZTAT H8/3048 Series

Бренд: Renesas Страницы: 34

Бренд: Garland Страницы: 6

Бренд: FS Страницы: 19

Бренд: Zoom Страницы: 88

Vortex86SX VSX-6100

Бренд: ICOP Technology Страницы: 50

DAS-1800HR Series

Бренд: Keithley Страницы: 139

DynaGST/2402G GEP-33224T-1

Бренд: UNICOM Страницы: 17

Fast EtherLink XL PCI 10/100BASE-TXNetwork Interface...

Бренд: 3Com Страницы: 12

Бренд: ZALMAN Страницы: 20

VAR-SOM-MX8M-PLUS

Бренд: Variscite Страницы: 2

Бренд: ETAS Страницы: 68

Бренд: Maestro Wireless Solution Страницы: 22

Бренд: Microcomputer Systems Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды