Cisco aironet 1130 Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 184

background image

162

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Adding and Managing Mesh Access Points with Cisco WCS

Figure 96

Link Test Results

Step 5

To view a graphical representation of SNR statistics over a period of time, click the arrow on the link. A
window with multiple SNR graphs appears (see

).

The following graphs are displayed for the link:

•

SNR Up

—

Plots the

RSSI values of the neighbor from the perspective of the mesh access point.

•

SNR Down

—

Plots the RSSI values that the neighbor reports to the mesh access point.

•

Link SNR

—

Plots a weighed and filtered measurement based on the SNR Up value.

•

The Adjusted Link Metric

—

Plots the value used to determine the least cost path to the root mesh access

point. This value is the ease to get to the rooftop access point and accounts for the number of hops. The
lower the ease value, the less likely the path is used.

•

The Unadjusted Link Metric

—

Plots the least cost path to get to the root access point unadjusted by the

number of hops. The higher the value for the unadjusted link, the better the path.

«
...
160
161
162
163
164
...
»

Содержание aironet 1130

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для aironet 1130

Бренд: Abus Страницы: 60

Бренд: Idis Страницы: 123

Бренд: Idis Страницы: 29

Бренд: Idis Страницы: 28

DirectIP DR-1304P

Бренд: Idis Страницы: 82

Бренд: iDirect Страницы: 130

Бренд: YASKAWA Страницы: 68

Бренд: Google Страницы: 14

Procont LMC-008-IO

Бренд: janitza Страницы: 28

Enterasys Matrix 2G4082-25

Бренд: Enterasys Страницы: 58

Бренд: TP-Link Страницы: 87

UM10301 PCA8565

Бренд: NXP Semiconductors Страницы: 54

Бренд: AMX Страницы: 1

Бренд: Alula Страницы: 4

Бренд: Digisol Страницы: 81

Бренд: US Robotics Страницы: 180

Бренд: PRIZM Страницы: 8

Бренд: Paradyne Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды