Cisco aironet 1130 Скачать руководство пользователя страница 133

Страница: 133 / 184

133

Cisco Aironet 1520, 1130, 1240 Series Wireless Mesh Access Points, Design and Deployment Guide, Release 6.0

OL-20213-01

Checking the Health of the Network

Figure 81

All APs > Access Point Name > Mesh Neighbor Stats Window

Click

Back

to return to the All APs >

Access Point Name

> Neighbor Info window.

Using the CLI to View Neighbor Statistics for a Mesh Access Point

Use these commands to view neighbor statistics for a specific mesh access point using the controller CLI.

•

To view the mesh neighbors for a specific mesh access point, enter this command:

show mesh neigh {detail | summary}

AP_Name

Information similar to the following appears when you request a summary display:

AP Name/Radio Mac Channel Snr-Up Snr-Down Link-Snr Flags State

----------------- ------- ------ -------- -------- ------ -------

mesh-45-rap1 165 15 18 16 0x86b UPDATED NEIGH PARENT BEACON

00:0B:85:80:ED:D0 149 5 6 5

0x1a60 NEED UPDATE BEACON DEFAULT

00:17:94:FE:C3:5F

149 7 0

0x860 BEACON

•

To view the channel and signal-to-noise ratio (SNR) details for a link between a mesh access point
and its neighbor, enter this command:

show mesh path

AP_Name

Information similar to the following appears:

AP Name/Radio Mac Channel Snr-Up Snr-Down Link-Snr Flags State

----------------- ------- ------ -------- -------- ------ -------

mesh-45-rap1 165 15 18 16 0x86b UPDATED NEIGH PARENT BEACON

mesh-45-rap1 is a Root AP.

•

To view the percentage of packet errors for packets transmitted by the neighbor mesh access point,
enter this command:

show mesh per-stats

AP_Name

Information similar to the following appears:

Neighbor MAC Address 00:0B:85:5F:FA:F0

Total Packets transmitted: 104833

Total Packets transmitted successfully: 104833

Total Packets retried for transmission: 33028

Neighbor MAC Address 00:0B:85:80:ED:D0

Total Packets transmitted: 0

Total Packets transmitted successfully: 0

Total Packets retried for transmission: 0

Содержание aironet 1130

























































































































































































Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды

Cisco aironet 1130, Руководство по проектированию и развертыванию

Результаты поиска

Содержание aironet 1130

Отзывы:

Похожие инструкции для aironet 1130

Бренды по названию

Популярные бренды