Cisco 831 - 831 EN Broadband Router Скачать руководство пользователя | Manualshive

Страница: 26 / 62

background image

Chapter 2 Installation

Preparing for Installation

2-2

Cisco 831 Router and SOHO 91 Router Hardware Installation Guide

78-14784-02

Warnings

Before installing the router, read the following warnings:

Warning

Read the installation instructions before you connect the system to its power
source.

Warning

Only trained and qualified personnel should be allowed to install, replace, or
service this equipment.

Warning

No operator serviceable parts inside. Refer servicing to qualified personnel.

Warning

Before working on a chassis or working near power supplies, unplug the power
cord on AC units; disconnect the power at the circuit breaker on DC units.

Warning

This equipment is intended to be grounded. Ensure that the host is connected to
earth ground during normal use.

Warning

This product relies on the building’s installation for short-circuit (overcurrent)
protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S.
(240 VAC, 10A international) is used on the phase conductors (all
current-carrying conductors).

Warning

Before working on equipment that is connected to power lines, remove jewelry
(including rings, necklaces, and watches). Metal objects will heat up when
connected to power and ground and can cause serious burns or weld the metal
object to the terminals.

«
...
24
25
26
27
28
...
»

Содержание 831 - 831 EN Broadband Router































































Отзывы:

Нет отзывов

Похожие инструкции для 831 - 831 EN Broadband Router

Бренд: Habitat Страницы: 48

Бренд: Draytek Страницы: 8

Бренд: Google Страницы: 14

Бренд: QNAP Страницы: 39

Sentry Global Security Modem

Бренд: Server Technology Страницы: 22

NSLU2 - Network Storage Link NAS Server

Бренд: Linksys Страницы: 64

Бренд: TRENDnet Страницы: 62

Бренд: 4G Systems Страницы: 2

Бренд: Eneo Страницы: 68

Бренд: Abocom Страницы: 63

ACCULINK 3161 CSU

Бренд: Paradyne Страницы: 19

Бренд: Zhone Страницы: 2

Бренд: National Instruments Страницы: 26

Бренд: Lantronix Страницы: 75

Бренд: Zhone Страницы: 28

HFisolator 9730/26-11

Бренд: Stahl Страницы: 2

Network Adapter AC AAP

Бренд: Extron electronics Страницы: 2

Бренд: H3C Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды