Cisco 7821 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 360

background image

Valid values are:

• Null

• 128 to 149

• 151 to 158

• 161 to 254

Set the

DHCP VLAN Option

value to

Null

to disable the voice VLAN configuration.

Cisco recommends that you use DHCP Option 132.

Step 3

Click

Submit All Changes

.

What to do next

In the

VLAN Settings

section of the

Voice

>

System

tab, you can configure these settings:

• Cisco Discovery Protocol (CDP)

• LLDP-MED

• Network Startup Delay

• VLAN ID

• DHCP VLAN Option

SIP and NAT Configuration

SIP and the Cisco IP Phone

The Cisco IP Phone uses Session Initiation Protocol (SIP), which allows interoperation with all IT service
providers that support SIP. SIP is an IETF-defined signaling protocol that controls voice communication
sessions in an IP network.

SIP handles signaling and session management within a packet telephony network.

Signaling

allows call

information to be carried across network boundaries.

Session management

controls the attributes of an

end-to-end call.

In typical commercial IP telephony deployments, all calls go through a SIP Proxy Server. The receiving phone
is called the SIP user agent server (UAS), while the requesting phone is called the user agent client (UAC).

SIP message routing is dynamic. If a SIP proxy receives a request from a UAS for a connection but cannot
locate the UAC, the proxy forwards the message to another SIP proxy in the network. When the UAC is
located, the response routes back to the UAS, and the two UAs connect using a direct peer-to-peer session.
Voice traffic transmits between UAs over dynamically assigned ports using Real-time Protocol (RTP).

RTP transmits real-time data such as audio and video; RTP does not guarantee real-time delivery of data. RTP
provides mechanisms for the sending and receiving applications to support streaming data. Typically, RTP
runs on top of UDP.

Cisco IP Phone 7800 Series Multiplatform Phones Administration Guide

52

Cisco IP Phone Installation

SIP and NAT Configuration

«
...
64
65
66
67
68
...
»

Содержание 7821









































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7821

Бренд: Gembird Страницы: 14

Бренд: Jabra Страницы: 3

Бренд: Plantronics Страницы: 1

Бренд: Jabra Страницы: 16

Бренд: BlueWear Страницы: 27

Бренд: Iluv Страницы: 20

Бренд: Razer Страницы: 19

Crossfade II Wireless

Бренд: V-Moda Страницы: 27

Бренд: Jabra Страницы: 14

Бренд: Fire Com Страницы: 12

Бренд: Voxoa Страницы: 4

Бренд: Takstar Страницы: 3

Бренд: Hama Страницы: 200

Бренд: Hama Страницы: 10

Бренд: Garmin Страницы: 12

Бренд: Marley Страницы: 6

Pro 925 Dual Connectivity

Бренд: Jabra Страницы: 4

Бренд: Jabra Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды