manualshive.com logo in svg

Cisco 7821, Руководство администратора

Пользовательский мануал для продукта NCI 7821 доступен для загрузки бесплатно на manualshive.com. Скачайте руководство по эксплуатации и узнайте все секреты работы с устройством. Не забудьте загрузить свой мануал прямо сейчас!

Поделиться
Скачать
background image

If the VLAN is not set by CDP and LLDP-MED, the VLAN ID that is configured manually is used. If the
VLAN ID is not configured manually, no VLAN is supported. DSCP is used and the network policy determines
LLDP-MED if applicable.

LLDP-MED and Multiple Network Devices

You can use the same application type for network policy. However, phones receive different Layer 2 or Layer
3 QoS Network policies from multiple network connectivity devices. In such a case, the last valid network
policy is accepted.

LLDP-MED and IEEE 802.X

The Cisco IP Phone does not support IEEE 802.X and does not work in a 802.1X wired environment. However,
IEEE 802.1X or Spanning Tree Protocols on network devices could result in delay of fast start response from
switches.

Configure VLAN Settings

Before you begin

Access the phone administration web page. See

Access the Phone Web Page, on page 80

.

Procedure

Step 1

Select

Voice

>

System

.

Step 2

In the

VLAN Settings

section, configure the fields.

Step 3

Click

Submit All Changes

.

Set Up DHCP VLAN Option from Phone Web Page

.

You can add a predefined DHCP option to configure the voice VLAN for your phone.

Before you begin

• Access the phone administration web page. See

Access the Phone Web Page, on page 80

.

• Disable CDP/LLDP and manual VLAN.

Procedure

Step 1

Select

Voice

>

System

.

Step 2

In the

VLAN Settings

section, enter a value in the

DHCP VLAN Option

field.

The field is empty, by default.

Cisco IP Phone 7800 Series Multiplatform Phones Administration Guide

51

Cisco IP Phone Installation

LLDP-MED and Multiple Network Devices

Содержание 7821









































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7821

Jabra IBM lotus sametime User Manual preview
IBM lotus sametime
Бренд: Jabra Страницы: 4
Sigtronics SE-2RVC Instructions preview
SE-2RVC
Бренд: Sigtronics Страницы: 2
Logitech Wireless Headset Getting Started With preview
Wireless Headset
Бренд: Logitech Страницы: 2
Krüger & Matz KM0490 Owner'S Manual preview
KM0490
Бренд: Krüger & Matz Страницы: 56
NEC C124 User Manual preview
C124
Бренд: NEC Страницы: 22
NEC DTP-16HC User Manual preview
DTP-16HC
Бренд: NEC Страницы: 3
NEC DTP-16HC - Dterm Handset Cordless Telephone User Manual preview
DTP-16HC - Dterm Handset Cordless Telephone
Бренд: NEC Страницы: 3
NEC C944 User Manual preview
C944
Бренд: NEC Страницы: 53
NEC UNIVERGE MH240 Features & Specifications Manual preview
UNIVERGE MH240
Бренд: NEC Страницы: 2
NEC MH110 Brochure preview
MH110
Бренд: NEC Страницы: 4
NEC M166C Customer Engineer Manual preview
M166C
Бренд: NEC Страницы: 56
NEC MH110 Administration Manual preview
MH110
Бренд: NEC Страницы: 62
NEC G966 Basic User'S Manual preview
G966
Бренд: NEC Страницы: 101
Jabra Step Wireless User Manual preview
Step Wireless
Бренд: Jabra Страницы: 14
Cyber Blue BH13 Manual preview
BH13
Бренд: Cyber Blue Страницы: 12
THOMSON WHP-6005BT Operating Instructions Manual preview
WHP-6005BT
Бренд: THOMSON Страницы: 72
THOMSON WHP-6007B Operating Instruction preview
WHP-6007B
Бренд: THOMSON Страницы: 74
T'nB CBHOME Instructions Manual preview
CBHOME
Бренд: T'nB Страницы: 26

Бренды по названию

Популярные бренды

Загрузить еще бренды