Cisco 7821 Скачать руководство пользователя страница 326

Страница: 326 / 360

Solution

Verify the following:

The Ethernet cable is attached.

The Third-Party Call Control system is active.

Enable audio server debug and capture logs on both phones, then examine the logs.

Phone Does Not Recognize DTMF Digits or Digits Are Delayed

Problem

The user complains that numbers are missed or delayed when the keypad is used.

Cause

Pressing the keys too quickly can result in missed or delayed digits.

Solution

Keys should not be pressed rapidly.

Feature Troubleshooting

Here is troubleshooting information related to some of the phone features.

ACD Call Information Missing

Problem

A call center phone does not see call information during a call.

Solution

• Check the phone configuration to determine if

Call Information Enable

is set to yes.

• Check the Broadsoft server configuration to determine if the user's Device Profile is configured with

“Support Call Center MIME Type”.

Phone Doesn't Show ACD Softkeys

Problem

The phone doesn't display the Agent Sign In or Agent Sign Out softkeys.

Solution

• Check Broadsoft server configuration to determine if that user has been configured as a call center agent.

Cisco IP Phone 7800 Series Multiplatform Phones Administration Guide

312

Cisco IP Phone Troubleshooting

Phone Does Not Recognize DTMF Digits or Digits Are Delayed

Содержание 7821









































































































































































































































































































































































Результаты поиска

Содержание 7821

Отзывы:

Похожие инструкции для 7821

Бренды по названию

Популярные бренды

Cisco 7821, Руководство администратора

Результаты поиска

Содержание 7821

Отзывы:

Похожие инструкции для 7821

Бренды по названию

Популярные бренды