Cisco 7300-1OC12POS-MM Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 50

background image

4-11

OC12 Packet Over SONET Line Card Installation and Configuration

OL-3437-01

Chapter 4 Configuring the OC12 POS Line Card

Checking the Configuration

Using the show interfaces Command

The show interfaces command displays status information (including the physical slot and interface
address) for the interfaces you specify. All of the examples that follow specify POS interfaces.

Note

The outputs that appear in this document may not match the output you receive when running these
commands. The outputs in this document are examples only.

Cisco 7304 Router

Following is an example of the show interfaces command for an OC12 POS line card in slot 3 of a Cisco
7304 router:

Router#

show interfaces pos 3/0

POS3/0 is up, line protocol is up

Hardware is Packet over Sonet

MTU 4470 bytes, BW 622000 Kbit, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation HDLC, crc 16, loopback not set

Keepalive set (10 sec)

Scramble disabled

Last input 00:00:07, output 00:00:07, output hang never

Last clearing of "show interface" counters never

Input queue:0/75/0/0 (size/max/drops/flushes); Total output drops:0

Queueing strategy:fifo

Output queue :0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

1 packets input, 24 bytes

Received 1 broadcasts, 0 runts, 0 giants, 0 throttles

0 parity

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

1 packets output, 24 bytes, 0 underruns

0 output errors, 0 applique, 1 interface resets

0 output buffer failures, 0 output buffers swapped out

0 carrier transitions

Using the ping Command to Verify Network Connectivity

Using the ping command, you can verify that an interface port is functioning properly. This section
provides a brief description of this command. Refer to the publications listed in the

Documentation” section on page 8

for detailed command descriptions and examples.

The ping command sends echo request packets out to a remote device at an IP address that you specify.
After sending an echo request, the system waits a specified time for the remote device to reply. Each
echo reply is displayed as an exclamation point (!) on the console terminal; each request that is not
returned before the specified time-out is displayed as a period (.). A series of exclamation points (!!!!!)
indicates a good connection; a series of periods (.....) or the messages [timed out] or [failed] indicate a
bad connection.

Following is an example of a successful ping command to a remote server with the address 10.0.0.10:

Router#

ping 10.0.0.10 <Return>

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echoes to 10.0.0.10, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 1/15/64 ms

«
...
45
46
47
48
49
...
»

Содержание 7300-1OC12POS-MM



















































Отзывы:

Нет отзывов

Похожие инструкции для 7300-1OC12POS-MM

Бренд: Farris Engineering Страницы: 12

Бренд: Eastern Times Technology Страницы: 4

Бренд: Vacon Страницы: 18

Бренд: Samson Страницы: 78

Бренд: Rachio Страницы: 16

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: QCON Страницы: 4

Бренд: Caen Страницы: 20

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

Бренд: C&C Страницы: 17

Бренд: SMC Networks Страницы: 10

Бренд: Netro Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды