Cisco 7300-1OC12POS-MM Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 50

background image

3-3

OC12 Packet Over SONET Line Card Installation and Configuration

OL-3437-01

Chapter 3 Removing and Installing Line Cards

Line Card Removal and Installation

Caution

To prevent jamming the carrier between the upper and the lower edges of the slot, and to ensure that the
connector at the rear of the line card mates with the connection at the rear of the slot, make certain that
the carrier is positioned correctly, as shown in the cutaway in the following illustration. If the line card
does not slide freely into the backplane, loosen the locking thumbscrews on the neighboring line cards.

Warning

When performing the following procedures, wear a grounding wrist strap to avoid ESD damage to the
card. Some platforms have an ESD connector for attaching the wrist strap. Do not directly touch the
midplane or backplane with your hand or any metal tool, or you could shock yourself.

Line Card Removal and Installation

In this section, the illustration that follows gives step-by-step instructions on how to remove and install
line cards in the following supported platform:

•

Cisco 7304—Removing and Installing a Line Card, page 3-4

«
...
31
32
33
34
35
...
»

Содержание 7300-1OC12POS-MM



















































Отзывы:

Нет отзывов

Похожие инструкции для 7300-1OC12POS-MM

Бренд: Eaton Страницы: 166

Бренд: S-COM Страницы: 400

Бренд: ZIMO Страницы: 38

Бренд: Garmin Страницы: 220

Бренд: Gardena Страницы: 16

Бренд: Data Signs Страницы: 23

Бренд: HQ Power Страницы: 23

653 - AE Series

Бренд: VAT Страницы: 103

Бренд: Scanreco Страницы: 10

Бренд: Teledyne Страницы: 102

ACTIVAL VY51 5H006

Бренд: Azbil Страницы: 20

Бренд: Firmtech Страницы: 19

Бренд: Yoshitake Страницы: 21

Бренд: Oasis Страницы: 7

Synergy SGY-101

Бренд: Fairford Страницы: 20

Бренд: Varian Страницы: 37

Бренд: Daikin Страницы: 8

Бренд: Silverline Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды