Cisco 2010 Скачать руководство пользователя страница 33

Страница: 33 / 92

2-9

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 2 Preparing for Router Installation

Required Tools and Equipment for Installation and Maintenance

Asynchronous/Synchronous Serial Module Baud Rates

The following baud-rate limitations apply to the slow-speed serial interfaces found in the
asynchronous/synchronous serial modules:

•

Asynchronous interface—Maximum baud rate is 115.2 kbps.

•

Synchronous interface—Maximum baud rate is 128 kbps full duplex.

Required Tools and Equipment for Installation and Maintenance

You need the following tools and equipment to install and upgrade the router and its components:

•

ESD-preventive cord and wrist strap

•

Number 2 Phillips screwdriver

•

Phillips screwdrivers: small, 3/16-in. (4 to 5 mm) and medium, 1/4-in. (6 to 7 mm)

•

Screws that fit your rack

In addition, depending on the type of modules you plan to use, you might need the following equipment
to connect a port to an external network:

•

Cables for connection to the WAN and LAN ports (dependent on configuration).

Note

For more information on cable specifications, see

Cisco

Modular Access Router Cable

Specifications

at www.cisco.com.

•

Ethernet hub or PC with a network interface card for connection to an Ethernet (LAN) port.

•

Console terminal (an ASCII terminal or a PC running HyperTerminal or similar terminal emulation
software) configured for 9600 baud, 8 data bits, 1 stop bit, no flow control, and no parity.

•

Modem for connection to the auxiliary port for remote administrative access (optional).

•

Data service unit (DSU) or channel service unit/data service unit (CSU/DSU) as appropriate for
serial interfaces.

•

External CSU for any CT1/PRI modules without a built-in CSU.

19200

7.6

513

156

16.4

38400

3.7

256

16.4

56000

8.6

2.6

102

16.4

1544000 (T1)

—

16.4

Table 2-2

Serial Signal Transmission Speeds and Distances (continued)

Distance for
EIA/TIA-232

Distance for X.21 and
V.35

Distance for USB

Rate (bps)

Feet

Meters

Feet

Meters

Feet

Meters

Содержание 2010





























































































Результаты поиска

Содержание 2010

Отзывы:

Похожие инструкции для 2010

Бренды по названию

Популярные бренды

Cisco 2010, Руководство по установке оборудования

Результаты поиска

Содержание 2010

Отзывы:

Похожие инструкции для 2010

Бренды по названию

Популярные бренды