Cisco 2010 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 92

background image

2-6

Cisco Connected Grid Routers 2010 Hardware Installation Guide

OL-21559-01

Chapter 2 Preparing for Router Installation

Network Cabling Specifications

EIA/TIA-232

Depending on the cable and the adapter used, this port appears as a DTE or DCE device at the end of the
cable. Only one port can be used at the same time.

The default parameters for the console port are 9600 baud, 8 data bits, no parity, and 1 stop bit. The
console port does not support hardware flow control. For detailed information about installing a console
terminal, see the

“Connecting to a Console Terminal or Modem” section on page 3-10

.

For cable and port pinouts, see

Cisco Modular Access Router Cable Specifications

USB Serial Console

The USB serial console port connects directly to the USB connector of a PC using a USB Type A to 5-pin
mini USB Type-B cable. The USB Console supports full speed (12Mb/s) operation. The console port
does not support hardware flow control.

Note

Always use shielded USB cables with a properly terminated shield.

The default parameters for the console port are 9600 baud, 8 data bits, no parity, and 1 stop bit. The
console port does not support mode control. For detailed information about installing a console terminal,
see the

“Connecting to a Console Terminal or Modem” section on page 3-10

For operation with Microsoft Windows, the Cisco Windows USB Console Driver must be installed on
every PC connected to the console port. If the driver is not installed, prompts guide you through a simple
installation process. For detailed information about installing the Cisco Windows USB Console Driver
see

“Installing the Cisco Microsoft Windows USB Device Driver” section on page 3-13

.

The Cisco Windows USB Console Driver allows plugging and unplugging the USB cable from the
console port without affecting Windows HyperTerminal operations. No special drivers are needed for
Mac OS X or Linux.

Only one console port can be active at a time. When a cable is plugged into the USB console port the
RJ-45 port becomes inactive. Conversely, when the USB cable is removed from the USB port the RJ-45
port becomes active.

Baud rates for the USB console port are 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps.

Note

4-pin mini USB Type-B connectors are easily confused with 5-pin mini USB Type-B connectors.
They are not compatible. Only the 5-pin mini USB Type-B can be used.

Auxiliary Port Connections

The router has an EIA/TIA-232 asynchronous serial auxiliary port (RJ-45) that supports flow control.
Depending on the cable and the adapter used, this port appears as a DTE or DCE device at the end of the
cable.

«
...
28
29
30
31
32
...
»

Содержание 2010





























































































Отзывы:

Нет отзывов

Похожие инструкции для 2010

Бренд: ZETR Страницы: 2

Бренд: CallDirect Страницы: 33

Бренд: Wave wifi Страницы: 2

Бренд: Garland Страницы: 4

Бренд: Hama Страницы: 10

Бренд: ICP DAS USA Страницы: 14

Бренд: ICP DAS USA Страницы: 25

Бренд: ICP DAS USA Страницы: 15

Бренд: ICP Страницы: 14

Бренд: Quick Eagle Networks Страницы: 4

Azure StorSimple 8100

Бренд: Microsoft Страницы: 12

Бренд: Supero Страницы: 112

Бренд: E-Lins Страницы: 113

NetIron MLXe Series

Бренд: Brocade Communications Systems Страницы: 305

Бренд: Juniper Страницы: 2

Бренд: CyberTAN Страницы: 67

Air Live GW-300R

Бренд: Ovislink Страницы: 20

EZ Switch SMC-EZ1024FDT

Бренд: SMC Networks Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды