Cisco 1100 Series страница 2 Скачать руководство пользователя

Страница: 2 / 14

Replacing the Chassis Cover

The Cisco 1100 Series ISRs have a removable cover.

Do not run the router with the cover off. Doing so can cause the router to overheat very quickly.

Use a number-2 Phillips screwdriver to perform the following tasks.

Removing the Cover

To remove the cover, perform the following steps.

Step 1

Read the Safety Warnings and disconnect the power supply before you perform any module replacement.

Step 2

Confirm the router is turned off and disconnected from the power supply or power supplies. If a redundant power is
used, disconnect from the redundant power supply.

Step 3

Place the chassis on a flat surface.

Step 4

Remove all the screws on the both sides of the router; seven on each side.

Step 5

Pull the cover to disengage the slots along the front (bezel) edge of the chassis, as shown in the figure below.

Figure 1: Removing the Cover

Slots

Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router

Installing and Upgrading Internal Modules and FRUs

Accessing Internal Modules

Содержание 1100 Series















Результаты поиска

Содержание 1100 Series

Отзывы:

Похожие инструкции для 1100 Series

Бренды по названию

Популярные бренды

Cisco 1100 Series, Установка и обновление

Результаты поиска

Содержание 1100 Series

Отзывы:

Похожие инструкции для 1100 Series

Бренды по названию

Популярные бренды