Cisco 10008 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 70

Cisco 10008 Скачать руководство пользователя страница 35

35

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

Managing the Router Using the Network Management Ethernet Port

Step 13

Reload the system by entering the

reload

command.

Router#

reload

Proceed with reload? [confirm]

Resetting .......

.

.

.

Both the PRE4 are now using the new Cisco IOS image with the new register settings.

Managing the Router Using the Network Management Ethernet
Port

The Network Management Ethernet (NME) port on the PRE4 is used to manage the Cisco 10008 router.
The duplex mode and speed of the NME port are configurable.

The following sections describe how to configure the duplex mode and speed of the NME port for the
PRE4.

Configuring the NME Port on the PRE4

The NME port for PRE4 supports the following operational modes:

•

Autonegotiation (the default)

•

Full-duplex

•

Half-duplex

Default configurations do not appear in the router’s configuration file.

We recommend that you allow the NME port to autonegotiate the duplex mode. When autonegotiation
mode is enabled, the NME port responds only to IEEE 802.3x pause frames from another device.

If the negotiation of duplex mode fails and a duplex mode mismatch occurs, manually set the duplex
mode for full-duplex or half-duplex operation. Setting duplex mode disables autonegotiation mode.
When you manually set duplex mode, the NME port does not support IEEE 802.3x flow control.

When you manually configure duplex mode, the NME port can experience problems. If this occurs,
disable duplex mode by entering the

no full-duplex

or

no half-duplex

command. When you enter the

no duplex

command, the operational mode reverts to autonegotiation mode.

To configure the NME port, perform the following optional configuration tasks:

•

Manually Setting the Duplex Mode for the NME Port for the PRE4, page 36

•

Manually Setting the Speed for the NME Port for the PRE4, page 36

«
...
33
34
35
36
37
...
»

Содержание 10008







































































Отзывы:

Нет отзывов