manualshive.com logo in svg

Cisco 10008, Руководство по установке и настройке, Страница: 20 / 70

Поделиться
Скачать
Cisco 10008 Скачать руководство пользователя страница 20

20

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

  Installing or Replacing a PRE4

Step 5

See the 

“Installing or Replacing a PRE4” section on page 11

 for instructions on how to install a new 

PRE.

Note

If you are not installing a replacement PRE, install a blank faceplate in the slot.

Warning

Do not operate the system unless all slots contain a PRE4, line card, or a blank faceplate. Blank 
faceplates are necessary in empty slots to prevent exposure to hazardous voltages, to reduce 
electromagnetic interference (EMI) that may disrupt other equipment, and to direct the flow of cooling 
air through the chassis.

Step 6

Power on the system if you have powered it off. 

Troubleshooting the Installation

Refer to 

Figure 2

 and 

Table 2

 for descriptions of the LEDs on the PRE4. Follow the instructions in 

Table 6

 to troubleshoot the installation.

Table 6

PRE4 Installation Troubleshooting

If these troubleshooting procedures do not correct the problem, refer to the

 Cisco 10000 Series Router 

Troubleshooting Guide

 for additional information.

Symptom

Possible Cause

Corrective Action

PEMs, fans, and other line cards 
do not operate

1.

Disconnected power cord.

2.

Power switch is in the Off 
position.

3.

The PRE4 fuses are blown.

1.

Check that all power cords 
are properly connected to 
both the chassis and at the 
power connection end.

2.

Set the PEM power 
switches to the On 
position.

3.

Replace the PRE4.

The FAIL LED does not light 
during the power-on self-test

1.

The PRE4 is not properly 
seated.

2.

Bad PRE4 slot or backplane 
connector.

1.

Be sure the ejector levers 
are fully closed and that 
the captive screws have 
been tightened.

2.

Remove the PRE4 and 
install it in another PRE4 
slot.

PRE4 does not operate properly

1.

Bad PRE4 slot or backplane 
connector.

2.

Bad PRE4.

1.

Remove the PRE4 and 
install it in another PRE4 
slot.

2.

Replace the PRE4.

Содержание 10008







































































Отзывы:

Нет отзывов