Cirrus Logic CS44600 Скачать руководство пользователя | Manualshive

Страница: 63 / 76

background image

DS633F1

63

CS44600

7.22.2

SRC Lock Interrupt (SRC_LOCK)

Default = 0

Function:

When high, indicates that on all active channels, the sample rate converters have achieved lock. This
interrupt is an edge-triggered event.

If this bit is set to a 1b, indicating a lock condition, and an SRC_UNLOCK condition is detected, then this
bit will be reset to 0b before a read of the Interrupt Status Register. Only the last valid state of the SRC
will be reported.

7.22.3

Ramp-Up Complete Interrupt (RMPUP_DONE)

Default = 0

Function:

When high, indicates that all active channels have completed the configured ramp-up interval.

7.22.4

Ramp-Down Complete Interrupt (RMPDN_DONE)

Default = 0

Function:

When high, indicates that all active channels have completed the configured ramp-down interval.

7.22.5

Mute Complete Interrupt (Mute_DONE)

Default = 0

Function:

When high, indicates that all muted channels have completed the mute cycle-down interval as defined by
the SZC[1:0] bits in the

“Volume Control Configuration (address 06h)” on page 55

.

7.22.6

Channel Over Flow Interrupt (OVFL_INT)

Default = 0

Function:

When high, indicates that the magnitude of an output sample on one of the channels has exceeded full
scale and has been clipped to positive or negative full scale as appropriate. This bit is the logical OR of
all the bits in the Channel Over Flow Status Register. Read the Channel Over Flow Status Register to
determine which channel(s) had the overflow condition.

7.22.7

GPIO Interrupt Condition (GPIO_INT)

Default = 0

Function:

When high, indicates that a transition as configured on one of the un-masked GPIO pins has occurred.
This bit is the logical OR of all the supported un-masked bits in the GPIO Status Register. Read the GPIO
Status Register to determine which GPIO input(s) caused the interrupt condition. The GPIO interrupt is
not removed by reading this register. The GPIO Status Register must be read to clear this interrupt. If the
GPIO input is configured as “edge trigger” the interrupt will clear. If the GPIO input is configured as “level
sensitive”, the interrupt condition will remain as long as the GPIO input remains at the active level.

«
...
61
62
63
64
65
...
»

Содержание CS44600













































































Отзывы:

Нет отзывов

Похожие инструкции для CS44600

Бренд: KEENZ Страницы: 24

Бренд: Eaton Страницы: 2

Бренд: Oceanic Страницы: 11

SHERPA MONOBLOC B0812

Бренд: Olimpia splendid Страницы: 44

Бренд: Olimpia splendid Страницы: 44

Бренд: Olimpia splendid Страницы: 16

Бренд: Keba Страницы: 16

Бренд: KEB Страницы: 16

Бренд: Zamel Страницы: 2

Бренд: Watts Страницы: 17

CIATControl OPC Server

Бренд: CIAT Страницы: 32

Бренд: Danfoss Страницы: 8

Infi 90 IMAOM01

Бренд: Bailey Страницы: 44

Бренд: asalvo Страницы: 46

Бренд: Westfalia Страницы: 18

Бренд: Eaton Страницы: 62

Бренд: Z-Wave Страницы: 27

Бренд: Bronpi Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды