Circutor EMK Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 20

Circutor EMK Series Скачать руководство пользователя страница 14

EMK

series

Instructions Manual M98118701-03-19A 14

•

Once ensured that the regulator is properly connected, adjust the regulator parameters for the

installation you are attempting to compensate. For this, follow the instructions of the particular

PF regulator manual, supplied with the equipment.

6.3 Tests once the capacitor bank is connected and the regulator has been adjusted

•

After start-up, make sure that the equipment is operating properly. A sign of proper operation,

once the steady state of the regulator has been reached, is a cos

ϕ

indication on the display

close to 1. In addition, the reactive energy meter should stop counting.

•

Check that the power supply voltage does not exceed the nominal value +10% (IEC 60831-1)

•

Check the current absorbed by each capacitor step. Under normal working conditions, it must

be close to the nominal values (see Table 7.4) and never more than 1.3 times this value. A

permanent consumption in all the capacitor steps over the nominal value, may be caused by

the presence of harmonics in the grid or by an excessively high power supply voltage. Both

circumstances are harmful for capacitors and control panels. If there is an unusual

consumption in only some of the capacitors, it is a sign that there are damaged capacitors.

•

In accordance with the IEC 60831-1 Standard, the capacitors are prepared to operate at the

permanent voltage assigned and with an overvoltage of up to 10% during 8 hours every 24

hours.

Check the working temperature of the capacitors after they have been operating for

24 hours. The capacitor case must be under 40ºC.

«
...
12
13
14
15
16
...
»

Содержание EMK Series





















Отзывы:

Нет отзывов