Cincoze CO-100/P2002 Series Скачать руководство пользователя страница 83

Страница: 83 / 104

100/P2002

Series | User Manual

4.7 Save & Exit

■

Save Changes and Exit

This item allows you to exit system setup after saving changes.

■

Discard Changes and Exit

This item allows you to exit system setup without saving changes.

■

Save Changes and Reset

This item allows you to reset the system after saving changes.

■

Discard Changes and Reset

This item allows you to reset system setup without saving any changes.

■

Save Changes

This item allows you to save changes done so far to any of the setup options.

■

Discard Changes

This item allows you to discard changes done so far to any of the setup options.

■

Restore Defaults

This item allows you to restore/ load default values for all the options.

■

Save as User Defaults

This item allows you to save the changes done so far as user defaults.

■

Restore User Defaults

This item allows you to restore the user defaults to all the options.

Содержание CO-100/P2002 Series









































































































Результаты поиска

Содержание CO-100/P2002 Series

Отзывы:

Бренды по названию

Популярные бренды

Cincoze CO-100/P2002 Series, Руководство пользователя

Результаты поиска

Содержание CO-100/P2002 Series

Отзывы:

Бренды по названию

Популярные бренды