Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 370

Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 52

Symptom:

P0071-AMBIENT TEMP SENSOR PERFORMANCE

When Monitored and Set Condition:

P0071-AMBIENT TEMP SENSOR PERFORMANCE

When Monitored:

Engine off time is greater than 480 minutes. Ambient temperature is

greater than -23°C(-10°F).

Set Condition:

After a calibrated amount of cool down time, the PCM compares the ECT

Sensor, IAT Sensor and the Ambient Air Temperature Sensor values. If the Ambient Air
Temperature Sensor value is not within a calibrated temperature amount of the other two
temperature sensors an error is detected. Two Trip Fault.

POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO

(K25) AAT SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE

AMBIENT AIR TEMPERATURE SENSOR VOLTAGE BELOW 1.0 VOLT

(K25) AAT SIGNAL CIRCUIT OPEN

(K4) SENSOR GROUND CIRCUIT OPEN

(K25) AAT SIGNAL CIRCUIT SHORTED TO GROUND

(K25) AAT SIGNAL CIRCUIT SHORTED TO (K4) SENSOR GROUND

PCM LOW

PCM HIGH

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t

, read DTCs and record the related Freeze Frame data.

Is the Good Trip Counter displayed and equal to zero?

All

Yes

→

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

46

DRIVEABILITY - NGC

«
...
50
51
52
53
54
...
»

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов